What to do if water flows from the tap and shower at the same time
Malfunctions in plumbing negatively affect comfort and quality of life. All details in the bathroom should be given due attention to avoid unexpected breakdowns. But sometimes malfunctions still take you by surprise. One of the problematic situations is the simultaneous supply of water from the tap and shower.
The content of the article
Reasons why water appears in the tap and shower at the same time
Water that pours from two points at once does not add convenience to using the bathroom. To solve a problem, you need to find out its cause. There may be several of them.
Drying and pressing of the gasket
The rubberized part becomes thinner. This leads to a violation of mode switching; the shutter cannot close tightly. Therefore, the water pressure is distributed unevenly.
If the problem is with the gasket, it needs to be replaced.
Important! There is not only one in the design, there are two of them. And both should be changed at once.
Abrasion of the rubber ring, malfunction of the button or oil seal
The rubber ring and its quality are among the most common failures.
Both of these faults occur for one of the following reasons:
- Poor quality faucet. The modern market offers a huge range of different price categories.Among them there are defective products and low quality parts. They have a short service life. Problems at work begin to appear quickly.
- Short-lived consumables. It is important to use not only a good faucet, but also high-quality elements when renovating. Otherwise, the breakdown will quickly recur.
You can fix such damage yourself. No special skills or knowledge required. However, it is important to use only high-quality parts. Then the problem will be fixed for a long time.
Troubleshooting
Before you begin any repairs, you need to review the safety precautions. Compliance with them will help you avoid unpleasant situations.
Safety regulations
- When performing any type of repair, first completely block the water. This applies to both hot and cold.
- Be sure to open the tap after this and check if water is flowing. This is because the valves can also be broken. Such actions will make sure that everything is really blocked.
- When working with hot water, it is important to be careful not to scald yourself.
- When tightening the fastener, it is important not to press too hard, otherwise you may damage the threads.
Repair work
There are several types of switches from tap to shower for faucets. These are rod ones that operate by pressing a button. Or ball ones, which trigger the switching mechanism by turning the part.
Depending on the breakdown, it may be necessary to replace the gasket, ring, or the entire switch.
Replacing the gasket
- After the water is turned off, open the tap and release any remaining pressure.
- Then remove the decorative trim, which hides the main part of the switch.
- Remove the bolt holding the parts and the handle.
- The switch itself is unscrewed using an adjustable wrench. You need to move counterclockwise.
- Remove the gasket from the structure and inspect it. If its condition is normal, it is enough to simply wash the part. But if it dries out, then they replace it with a new one. You can purchase the part at any plumbing store.
- The second one is located under the first gasket. To remove it, you need to remove the round nut and the stuffing box.
- When it was possible to get to the second gasket, it is also changed.
Replacing the ring
If the problem is in the rubber ring, it is also replaced with a new one. The technology is similar to that described above.
But to get to the part, you need to do more than just disassemble this part of the mixer. The adapter should be removed from the structure. You can use tweezers for this or simply push from below, where the hole has formed in the crank body.
Important! After replacing any part of the mixer, it must be reassembled in the reverse order.
Button repair
Problems may also arise with the button if a rod type switch is used.
If it simply does not return to its original position when pressed, then the spring has broken. The mixer is disassembled and the button is replaced with a new one.
Replacing the oil seal
But if the switch stops working completely, the problem is in the seal. It is located in the rod part of the switch. Repairs are carried out in the following order:
- Remove the button.
- Remove the rod.
- Replace with a new oil seal.
- The switch is assembled in the reverse order.
When completing the work, you should turn on the water and check whether the plumbing is working properly.
Correcting the situation when water flows from the shower and from the tap at the same time is not difficult. It is enough to find out which part is broken and replace it.We hope that you will not have any problems or difficulties during your work.