What can be done from an old bathtub?

After a bathroom renovation is completed, the old bathtub is usually thrown away. But if you awaken your imagination and make a little effort, then you can breathe a second life into an unnecessary thing and make an unusual art object for your dacha or home.

You can make a flowerbed out of an old summerhouse bathtub. To do this, the product is twisted into a bright color on the outer surface. Acrylic paints are used, as they are quite resistant to fading and exposure to the external environment. The bathtub can be painted a single color or made into a pattern.

If you don’t want to show off the old container, then you can partially bury it in the ground. And lay out the transition with pebbles, simulating an alpine slide. It is important that before pouring soil into the bath, you need to lay down a thick layer of drainage and drill small holes in the bottom so that moisture does not accumulate and the plant roots do not rot.

An alpine slide will look very impressive, if you use a round-shaped bathtub for it.

Another original solution would be a pond. To do this, the plumbing product should be buried and covered from the inside with natural and artificial stones. Use silicate glue as glue, as it is not susceptible to moisture.The pond will look very aesthetically pleasing if the entire surface of the bathroom is covered with stones and there is no metal showing through anywhere.

REFERENCE! If you don’t want to bother with glue, then you can paint the inner surface a dark color, dig it deep, level with the ground, and line it with decorative stones along the edges.

You can also make a bench for the garden. To do this, it is enough to saw off either the entire upper side surface, or do it partially. To prevent it from being cold when sitting on a metal bench, you can line the horizontal surface with wooden beams.

For a summer cottage, the bathtub can be used as a stove. In order to make such a device, you will have to put in a little effort. The cast-iron bathtub must be cut strictly in half, measuring the dimensions. At the end, which is oval in shape, it will be necessary to make a metal door. Attach awnings for it. Then supply electricity or equip a place for laying wood and make a grate so that you can place containers with food for cooking.

A garden bed made from an old bathtub requires very little effort. It is enough to install the product in the desired place in the garden.

Reference! To prevent the soil from rolling under the influence of water onto one of the edges of the sanitary ware, it is worth setting it strictly horizontally.

Drill evenly along the entire length of the bottom of the hole. They will ensure the drainage of excess moisture, which will allow the plants to grow fully. Then add a certain layer of drainage, and then lay the soil.

Important! Do not pour the soil flush with the sides. Otherwise, then it will start to spill over the edge.

If such a bed is planned for growing melons or those that require garter, then you should take care of this in advance. To do this, you can weld rods along one of the edges of the bath to the desired height. If you make them hook-shaped, bending upward, then you can most conveniently tie up any bush or provide support for a climbing plant.

In order to make a sofa from the bathroom, you need to cut out the front long side surface. Paint the remaining part with a suitable color of paint. In order for the paintwork to last as long as possible and look aesthetically pleasing, it is necessary to apply a metal primer underneath it. The legs of the product can be decorated with stucco elements. And to ensure seating comfort, sew special covers, which must have a thick layer of foam rubber. This will ensure softness.

In addition to the sofa, you can make a sofa out of the bathroom. To do this, you will have to cut out most of the side surface of the bathroom, leaving only one end side part with small bends. Moreover, make sure that the front bend is shorter in length.Whereas the back bend will extend approximately 1/3 of the length of the sanitary ware.

Next, a sequence of actions similar to the formation of a sofa is performed. That is, chipping of the inner and outer surfaces and legs occurs. Then sewing covers or pillows that provide softness for sitting.

In addition, you can make chairs. One sanitary ware will make two chairs. To do this, measure the bath and divide it in half. Why is the treatment carried out? Pre-clean, apply a primer, then the selected paint coating. After this, the chair is covered with special covers or lined with pillows. If you don’t want the product to stand on legs, you can put it on a wooden box. It will cover the legs of the old plumbing fixtures and create a visually appealing pedestal.

Before you start working with old plumbing fixtures, you should clean and degrease them. This will help the coating that will be applied later adhere better.

Important! To ensure that the paint lasts as long as possible and looks smooth, you need to apply one or two coats of primer. And after each application, let it dry thoroughly.

If you want to make the surface more glossy, then you need to apply a special varnish over the paintwork. In addition, such a three-layer painting will ensure resistance to aggressive environmental influences if the furniture or product is located in the open air.