Electrolux heater: instructions for use

If you want or have already purchased an Electrolux heater, we suggest you read its instructions. This article will be useful if you want to find out about the device or have lost the instructions for it. Below you will find out what the operating principle of the Electrolux heater is, the purpose and design of the Electrolux heater. Also below are instructions for using the Electrolux heater.

Electrolux heater, operating principle, purpose

The Electrolux electric heater is a convection-type household device for heating any type of room with an area of ​​up to 40 square meters.

This and similar heaters work as follows:

Convection always occurs in a room - air movement due to temperature differences. There is cold air at the bottom, it is heavier. There are air intake holes at the bottom of the heater through which cold air enters the heater. It has a heating element inside that heats up when electricity passes through it. The air blows over this element, taking heat from it, and exits through the air outlets back into the room.

Design/appearance of the Electrolux heater

The main elements of the heater from Electrolux:

• Air intake openings
• Air outlets
• Frame
• Control block
• A heating element
• Wheels/set of feet
• Air filter
• Temperature sensors

The heater control system/unit consists of:

• Display (LED)
• Temperature adjustment buttons
• Heating power adjustment buttons
• On/off buttons (it is also responsible for the timer)
• Power indicator

How to use an Electrolux heater: turning the device on/off, selecting a mode, adjusting the temperature, timer/self-shutdown.

Before using the device:

Take the device out of the box and remove the film from it. The film is glued to the front panel/front side. Check that the heater is turned off. If you wish, you can wipe the device with a dry cloth.

When you first start the heater, you may notice an unpleasant odor - the smell of burnt dust. Equipment sits on store shelves for a long time before it is purchased, so dust accumulates on it. When the device is turned on, the dust on its surface overheats and burns. The unpleasant smell that appears will soon disappear. If it smells burnt for a long time, the equipment may be defective. In this case, unplug the device from the outlet, inspect for damage, but do not open the device yourself if you do not want to void the warranty. If you find damage or there is still a smell after turning it on again, contact the service center.

It is not recommended to connect the device to the same outlet as other powerful devices. The outlet may not be able to withstand this (too much current). It will burn out and cause a short circuit.

Using the heater

Insert the plug from the device into the electrical outlet. The food must comply with the technical specifications.Immediately after this, the device will make a loud sound - this means that the device is turned on. The indicator on the control panel will light blue/blue – the heater is in standby mode (does not heat the room, waits for the user’s command).

Press the equipment on/off button and the device will switch to heating mode. The LED display will show the room temperature.

Operating mode

Select operating mode. There are two of them - half and full power. To select, press the on/off button. The display will then show HI or LO. The first value means the device operates at full power, the second – at half power. You can switch them using the button to the left of the start button.

To set the temperature, press the device's start button twice. The heating temperature will appear on the screen. To adjust it, use the lower buttons. One press – the heating temperature will increase/decrease by 1 degree Celsius. If you hold down the temperature increase/decrease button, the value will increase/decrease without stopping until it reaches the limit. The maximum value is 30 degrees Celsius, the minimum is 5. To save the changes, do nothing - after 5 seconds of inactivity, the device will return to operating mode, and the display will show the air temperature in the room.

How to turn on the timer on an Electrolux heater

To turn on the timer, press the on/off button three times. The display will show the time after which the device will turn off. The shutdown time is measured in hours. Initially, according to the factory settings, there will be 0. To adjust the shutdown time, use the temperature adjustment buttons under the start and mode selection buttons.Again, if you hold down one of these buttons, the time until shutdown will continuously increase or decrease. When you choose the time to turn itself off, leave the device alone. After 5 seconds of inactivity, the settings will be saved, the device will switch to heating mode, the timer will start counting, and the corresponding indicator will light up. When the time has expired, the device will turn off on its own - go into standby mode (the heating will turn off, the blue indicator will light up).

Shutdown

To turn off the Electrolux heater, you need to hold the power button for 3 seconds. Regardless of the operating mode, the heater will go into standby mode. After this, remove the plug from the socket.