How to use a chainsaw

A chainsaw is a complex and dangerous tool. During operation, you can get injured if you do not follow certain rules when working with it. Let's look at the features of using the tool.

How to use a chainsaw correctly: safety precautions

It is recommended that you read the instructions first. It contains all the necessary information about using a chainsaw. Before the beginning launch You should make sure that all equipment is in good working order. The chain brake is then activated. The saw must be installed on a level surface so that the sawing parts do not touch the ground. You can start launching.

To protect yourself from injury, you must use personal protective equipment, including gloves and special glasses.

You must work with the tool with extreme caution. The operator may be injured due to flying branches or contact with equipment elements. It is imperative to use a helmet to protect your head. Thick shoes will help avoid foot injuries.

To reduce the likelihood of injury, it is recommended that you adhere to the following rules:

1. The tool must be held as tightly as possible. It is better to press your arms closer to your body to reduce the load on them. The device must be constantly monitored.
2. It is forbidden to cut several logs at one time. Also, the work is not done with the tip of the saw. There is a high risk that it will slip. Before starting, the timber must be properly fixed.
3. The operator needs to take a position so that his body is not on the same plane as the operating chain. It is not recommended to bend over to avoid losing your balance.
4. The chain saw should not be used on materials above the user's shoulder level.

The described recommendations will help you preserve your health when operating a chainsaw.

How to cut with a chainsaw

In order for the process to be high-quality and fast, you must follow some recommendations. They depend on the material being processed.

Correct user position

To avoid injury and facilitate the process, the operator must take the correct position. This is a position in which the user can move away at any time if a dangerous situation arises. Before starting, the work area is cleared of small growths on which you can get caught and lose your balance.

The switched-on saw is held with both hands. The operator stands in the opposite direction from where the cut trees will fall.

How to cut down a tree correctly

It was noted that the process needs to begin with clearing the work area. When the small growth is eliminated, you need to decide in which direction the wood will fall. If an object is on a slope, it will fall in the direction where its center of gravity has shifted. A tree standing straight can be felled in any direction. You just need to take into account how the branches are located. This is due to the fact that it is much easier to knock the trunk to the side where it has more branches.

Then they make a wedge-shaped cut from the side where the tree will fall. Its depth should be no more than 1/3 of the trunk diameter. If the cut is done correctly, the tree will not tilt.

They move to the side opposite from the gash and rise a few centimeters up. A straight incision is made at this location. When a cut is made that causes the barrel to fall, the operator must be extremely concentrated. If the tree begins to fall without additional use of a fork or shovel, the person will have time to move away.

Thick trunks are much more difficult to cut down. If you have no experience in this process, it is better not to try. To fell a thick tree, you will need to use a tripwire. To do this, the cable should be secured to the trunk at a height of at least 5 meters. Then a wedge is cut out and the cable is pulled using a car or tractor. The trunk is trimmed on the side opposite to the wedge.

The process of felling thick trees is influenced by many factors, so it is dangerous for a beginner to perform such work.

How to cut branches

If you need to rid a fallen tree of its branches, you must act carefully. There is a risk that the tire will become pinched. The branches are cut down from the side opposite to the slope. You cannot use the tip of the splint for this. Elements may fly off and cause injury to the operator. With clamped branches they work from the load side. They often start to bounce, so before starting the sag it is recommended to move to a safe distance to avoid injury.

How to cut into logs

It is easier to cut a fallen tree than to cut it down to the roots. But there is also a certain danger here. If the work is performed incorrectly, the tire may become jammed in the trunk.Then it will be possible to remove it only with the help of a jack or crowbars. This will significantly complicate and slow down the process.

It is necessary to carefully inspect the trunk and begin cutting in areas where tension is present. It is recommended to start at the top of the head, gradually moving towards the butt. Both upper and lower cuts are allowed. In the first case, they act until the barrel drops, pressing the tire. Then they begin to cut the trunk from below. When the tree has been cut into several pieces, you can start sawing into logs using the top cut.

Working with a chainsaw must be carried out in full compliance with safety precautions. Careful preparation for the process and thinking through each action will reduce the likelihood of injury.