Converting a music center for USB

Most likely, many people still have old players, tape recorders or other music playing systems at home. It would be a shame to throw them away, and there is no point in leaving them at home. There is no need to worry, as there is an opportunity to give a second life to these “oldies”. Converting an old audio system to a USB connector is a very simple task, especially if it concerns a music center. This work does not take much time, and the cost is completely affordable.

What materials and tools are needed?

Rearranging various parts from audio systems is labor-intensive work and requires some experience. Naturally, you can adapt several old and unnecessary devices for assembly, but this will take quite a lot of time. It is much easier to use a ready-made purchased module.

Since modern technical innovations are updated all the time, Chinese manufacturers have pleased radio amateurs. Today, special audio modules are manufactured that can convert sound. Module features:

1. The simplest devices that are equipped only with a USB port.
2. Sophisticated devices that have a display to display information.
3. A certain number of ports for different needs.
4. A remote control with which the equipment is controlled.

However, the parts described above alone are not enough even to assemble the simplest audio system. For which you will need to use an old stereo system. It’s great if this audio system is still in working order. If the equipment is broken, then there is nothing to worry about. The most important thing is that the following elements are in working order:

1. A sound amplifier that is built into the audio system.
2. The speakers are from the old center, with the help of them you can listen to music.
3. A battery cell, or an element that is responsible for charging the battery.

Reference! You can purchase a module with different bells and whistles, but to revive an old cassette recorder, a regular device that is equipped only with a USB connector and can output high-quality sound is quite enough.

Important points before work

Connection diagrams for the audio module and music center are usually included with purchased devices, otherwise they can be easily found on the Internet. Modular equipment must have a constant voltage of 5 Volts. From 12 V, the module must be connected using a power supply (12/5 Volts). All work on altering the audio system must be carried out while observing safety precautions.

These homemade music players can be made as portable devices: it is much easier to carry a small music player around the apartment than a stationary audio system. From an old cassette recorder you can assemble a small music player with a USB port.

Converting a music center for USB: step by step

In order to install a sound module into an audio player, the music center will require minor disassembly.This is required to indicate the location where the device will be located.

However, do not forget that the installation must be carried out so that you can use the equipment from the remote control.

If you have some experience with electronics, you can solder the audio module to the wires. If electronics are not your thing, then you can mount the device into a cassette unit.

Once the installation location has been determined, you can proceed to connecting the sound module to the old audio system. The main stages of the work are as follows:

1. Taking a piece of wire, you need to connect the power and sound output. What you need is a circuit diagram of an audio module and a music player.
2. The work must be done very carefully, since the wires are powered by electricity.
3. Once you have completed connecting the wires, you can return to installing the board.
4. If the connector for cassettes is rejected, and it was decided to mount the audio module in another place, then you need to make a hole for USB.
5. Then you just need to connect the module output to the audio output board in the center. There are several ways to do this. The first is to solder to the circuit, the second is to connect using the aux input, if present.
6. We connect the power and check the functionality of the equipment.

Reference! You don't need to expect much from this audio system, since its potential is limited by the capabilities of the installed sound card. But to listen to your favorite musical compositions, an animated tape recorder is quite suitable.

Making a USB connector for a flash drive in an old player does not require much effort. You just need to purchase a special sound module and insert it into your old player.For a low cost you can get equipment that will play music tracks from a flash drive.