The speakers on the computer do not work, there is no sound

On your laptop you can watch your favorite TV shows and movies, and also have a good time playing an interesting computer game. This type of equipment is very convenient to take with you anywhere; it has compact dimensions, light weight and good performance. If you want to improve the quality of the output sound and achieve a full-fledged effect like in a movie theater, you can use speakers or special acoustic systems.

Thanks to the huge assortment and rapid development of production, you can find a wide range of equipment sold on store shelves. In order to purchase quality equipment, you should carefully study all the characteristics of the speakers and compare advanced models. For convenience, you can see the rating of the best devices in this category.

Sometimes, when putting the system into operation, various problems may arise. The most important of these is the lack of sound. To cope with this situation, it is necessary to correctly diagnose and begin troubleshooting. In our article we will talk about possible causes of problems and ways to correct the operation of the speakers. Depending on the type of malfunction, the algorithm of actions may vary significantly, so for convenience, we will consider each of the options.

IMPORTANT: Do not try to disassemble the equipment if you doubt your capabilities. Contact a specialized service center for assistance.

There is no sound from the laptop to the speakers: reasons

Connecting speakers to a laptop is not difficult; usually the entire system is connected quite simply. For convenience, you can use the instruction manual or included instructions. But sometimes problems may arise when outputting sound to a speaker system; in some cases, there may be no playback at all. In order to correctly assess the cause of the problem and begin to eliminate it, it is necessary to determine the source. Most often, problems can arise for the following reasons:

• Breakage or mechanical damage to the speaker housing.
• Kinking and breakage of wires at the junction with the speakers.
• If dust, large particles of dirt or drops of water get inside the equipment casing, the chips may come off.
• Faulty connection of wiring, chips and boards.
• Damaged speaker port (wired connection) or low battery (wireless versions).
• The drivers are not installed on the laptop, or their version is outdated.
• Software infection by a virus or malware that blocks the operation of applications.
• The settings have failed and the volume level has been set to the minimum value.

If possible, perform self-diagnosis and troubleshooting. If this is not possible, contact the technical support center for assistance to perform a detailed check of all systems.

IMPORTANT: It is not recommended to disassemble the equipment yourself, since working with electronics requires experience and appropriate education.

How can I get the sound back?

Once you have identified the cause of the problem, you can begin to take action to eliminate it. If you wish, you can contact the workshop, we will tell you how to solve the problem yourself. To understand the work plan, follow the step-by-step instructions, perform all actions in a certain sequence described below:

1. First of all, find out what exactly the problem is. Try pairing the speaker system with other equipment. If everything works, it means there is a problem with the laptop and you will have to work with it.
2. If there is no sound output even after pairing with another laptop, you should configure and repair the speakers.
3. Make sure the equipment is connected to a power source and check the pairing with the computer. After that, start identifying the problem and solving it.
4. First, clean all the elements to remove any existing dirt and get rid of any remaining accumulated moisture inside the case.
5. After this, inspect the external condition of the equipment. There may be defects in the speaker housing and wire circuit. Additionally, you can use multimeters to detect where the cord is damaged. If you have experience, you can solder the wiring or change the speakers.
6. Check the condition of USB connectors and adapters for connecting equipment. When using wireless types of speakers, make sure the battery has sufficient charge. If necessary, correct any deficiencies found.
7. Check the documentation for compatibility of the speaker system with the PC version. Despite advanced developments and the active implementation of universal coupling methods, some manufacturers specifically create products with a narrow spectrum of action.

REFERENCE! The proposed options involve repairing the speaker system with the possible replacement of components; we will talk about the method of settings via a PC further.

It is impossible to write an exact algorithm for solving the problem, since the method of solving the problem depends on the characteristics of each specific case. Try to look through all the options, starting with the most obvious, so you can decide on the task. After this, take measures to repair it yourself or contact a specialist.

What to do if the laptop sees the speakers, but there is no sound?

If the laptop recognizes the connected speaker system, then the connection is correct and the problem is definitely not in the wiring. Try pressing the power button on the panel of the speaker itself and adjusting the volume. This can be done using the buttons on the body of your equipment or through a laptop.

In the last option, click on the speaker icon in the lower right corner, raise the slider to the desired volume level from 0% to 100%. After this, go to the properties and playback parameters to regulate all indicators and configure the operation of the equipment.

What if the laptop doesn’t see the speakers? Compared to the previous one, this option is less common. The first step is to restart your laptop. To do this, close all programs, turn off the equipment, wait 10-15 minutes and turn everything on again. Typically, this situation occurs when working for a long time without interruption and with a large number of open and active applications. The system cannot cope with the load and power; a break can quite help in this case.

If this does not help, you need to proceed further according to the scheme:

1. Go to the “device manager” via the “start” and “control” keys.
2. From the proposed list of available and connected devices, find the speaker you need. If there is an exclamation point in a yellow triangle opposite it, it means you need to reinstall the drivers or update their version to the latest by downloading it from the official website. At the same time, check the functioning status of other connected devices and update their drivers if necessary.
3. Open the Run dialog box using the win and R key combination or using the start button in the main menu. In the window that opens, enter the request services.msc, and then confirm your entry with the Enter key. In the window that appears, select Windows Audio and activate automatic startup of the device and output of sound through it.
4. Additionally, select the default sound output technique from the “sound” menu.