How to connect a joystick to Xbox One

To use the game console, you must connect a joystick. This is very easy to do, just turn on both devices and perform a series of actions by pressing certain keys.

What you need to connect

To connect, you only need a console and a gamepad. We need to press the appropriate buttons to turn it on. But remember, if the set-top box does not have drivers, you must first install them. And wireless models will not work without a receiver that is inserted into the USB connector. Wireless devices require Bluetooth. The receiver can be purchased at the same store as the joystick.

What problems may arise

The most common problem is that the console does not accept the gamepad. Try the following:

1. Pull the cable out of the USB connector and put it back. Check the port, plug and cable for external damage. But the problem may also affect the inside of the wire, for example, the insulation layer is damaged or the contacts are stuck. In such cases, contact the service center.
2. If the connection is wireless, try connecting the device again. Make sure bluetooth is turned on and working.
3. Reboot your device.
4. Restart your controller by pressing the Xbox key and holding it for 5 seconds. Turn on the device by pressing this button again.

If all of the above methods do not help, there is a high probability of damage to the cable or port. Then repairs are needed.In this case, you need to take the joystick to a service center or buy a new one. If you understand how a gamepad works, you can do it yourself.

Reference! Another problem: I managed to connect the joystick, but it doesn’t work. This nuisance is rare. We need to establish the connection again. If the connection is wireless, there is a high probability that some device is causing interference (this applies to Wi-Fi and Bluetooth devices). You should use the joystick away from them.

The last problem is that the gamepad is outdated. Some modern games do not support older versions of gamepads. Unfortunately, repairs are not possible, all that remains is to buy modern equipment.

There are some notes to take into account:

1. One console can work with no more than 8 joysticks at the same time.
2. You need to assign a joystick specifically to the user who will be holding it (something like an account).

Connecting a joystick to xbox one: step by step

To connect the gamepad to the console you need to do the following:

1. We turn on the console.
2. Insert batteries or accumulators into the joystick. To do this, open the cover on the back panel.
3. Turn on the joystick by pressing the key and holding it down for 3 seconds. The key is located in the middle at the top of the device.
4. The Xbox button should start flashing. This signals that the device is turned on.
5. If the joystick still does not turn on, check the batteries. They may have already sat down. Also make sure you place them correctly. Try using the batteries on another device. Same with the battery.
6. Now press the connect button on the set-top box. There is no need to clamp it.For the Xbox One X and Xbox One S versions of the console, the key is located on the front panel on the right side, under the power key. It is small and round. And for the Xbox One version, the key is located on the side panel near the corner (where the disk drive is).
7. Now you need to connect the gamepad. To do this, press the round key on the top panel (if you hold the device in your hands). You need to hold down the key and hold it for about 20 seconds. You need to wait until the Xbox key on the joystick blinks several times. This means the console is being searched. While the joystick is connected, the Xbox key will be lit.
8. If we need to connect augmented gamepads, just repeat these steps with them.

Using an adapter cable and a USB connector

Most types of set-top boxes have a USB port for wired devices. Connecting them is simple; you just need to insert the USB plug into the appropriate connector. In such cases, the gamepad can work without batteries.

Connecting the gamepad to the console is very simple. You need to check what type of connection is being used, press the appropriate keys, and if problems arise, try rebooting the entire system.