Learn how to repair a washing machine door. How to disassemble the door with your own hands?

The washing machine door consists of several elements, each of which can fail for various reasons. For example, the latch is broken or the glass is broken, or the device that blocks the hatch does not work. Repairing a washing machine door in different situations is described step by step in this article.

How to open a broken lock

Replacing your washing machine door starts with unlocking the lock to get your laundry out and then getting started with the repair. Even if the handle breaks off, this can be done using improvised means, for example, using a spoon. You need to do this:

1. Choose a spoon of the required length and width, since the blocker in different models is located closer or further.
2. See the middle part of the hatch.
3. Take a spoon and insert the handle into the gap between the housing panel and the door.
4. Carefully move to the sides and feel for the desired part.
5. After this, you can press on the spoon and the door will open.

It is usually not possible to do this the first time. Therefore, it is recommended to move the spoon vertically, since the blocker may be slightly higher or lower.

If the washing machine door is broken, you can also open it using the emergency lever, which can be found below. It is usually installed next to the drain filter.However, not all models have this device, so you have to do it manually.

How to disassemble the door

After the hatch is opened and the clothes are removed, the repair of the washing machine door begins. To do this, proceed as follows:

1. Unplug the plug from the socket.
2. Close the cold water tap.
3. Unscrew the hinge mounting bolts, and then remove the washing machine door fastening.
4. Remove the door and place it on a flat surface.
5. Unscrew the screws that run along the inner contour. They are very small - you need to prepare a bag or small container in advance.
6. Now you need to remove the glass by opening the latches.
7. Inside you can find a metal rod. It is removed and all parts of the lock are taken out - it is necessary to disassemble the plastic, remove the spring with the latch and the connecting element.

After this, you need to purchase new parts and install them in place of the old ones. It is important to understand how to disassemble a washing machine door and perform repairs correctly. Even if one element is broken, you should replace everything, because the rest may not fit the new spare part. To install a new handle, install new parts:

1. First, install the spring.
2. Then install the clamp, holding it with a screwdriver.
3. They place the pin, but not completely yet.
4. Place a new plastic handle onto the latch.
5. Now you can push the pin all the way.

It should be understood that each model has its own characteristics. For example, instructions on how to disassemble the door of an Electrolux washing machine may differ slightly from other devices. Although in general it is exactly the same - the main steps are the same.

If the blocker is broken

This is an important element, which is called the hatch blocking device (abbreviated UBL).It may become damaged due to careless handling or wear out due to prolonged use. If the door of the washing machine is broken, it is often necessary to repair the lock.

You can also do this yourself; all you need is a set of screwdrivers. The sequence of actions is as follows:

1. The clamp is pryed up using a slotted screwdriver and removed.
2. Remove the fragment of the rubber cuff, which is located in the part where the lock is attached.
3. Next, unscrew the 2 screws that secure the locking mechanism.
4. Now you need to figure out how to remove the door from the washing machine. The device is removed manually and the chip is pulled off.
5. They install a new blocker and tighten the screws.
6. Put the cuff on and put the clamp back on.

Latch repair

The question of how to remove the washing machine door may not arise if the problem is only related to the latch. This reason can be determined by the absence of a click at the moment when the hatch closes. Also, notches appear on the lever that fits into the hole - it is they that interfere with normal closure.

During repairs, proceed as follows:

1. Unscrew the fasteners and remove the door as described above.
2. Remove nicks with a file.
3. Apply graphite-based lubricant to avoid damaging clothing.
4. Next, put the door back in place.

As you can see from this review, replacing a washing machine door is quite simple and does not require special tools or skills. Prepare a set of screwdrivers, as well as a small container for self-tapping screws, and remove each element step by step, after which they install new spare parts and check how the blocker works.