Zanussi washing machine: faults, do-it-yourself repairs at home

In case of malfunctions of the Zanussi washing machine, DIY repairs are possible. But first you need to accurately determine the cause, and then eliminate the malfunction. If there are doubts about the correctness of the diagnosis or a complex element (electronics) has broken down, it is recommended to call a specialist.

Spin and drain problems

Often the causes of breakdown are due to the fact that the machine does not completely drain the residual water or does not wring out the clothes well. As a result, it comes out too wet and not dried enough. Before you start repairing a Zanussi washing machine with your own hands, you need to make sure that the diagnosis is correct.

The device itself will show 1 of 3 error codes on the display:

• E21;
• E23;
• E24.

You can fix the problem yourself. To do this, it is recommended to proceed as follows:

1. Turn off the supply tap and unplug the washing machine from the socket.
2. Wait until it cools down (including the powder).
3. Open the panel.
4. Remove the drain hose and plug it.
5. Turn the pump cover counterclockwise.
6. Remove excess objects from the hose (if any).

If the pump blades rotate freely, you can screw the cover back on and put the panel back in place. To make sure that the device is working properly, you just need to drain the water without clothes (idle).

If this does not help, repairing a Zanussi washing machine with your own hands should affect other elements:

• filter - to clear it of blockages, you need to remove the element and rinse thoroughly;
• pipe that connects the pump and tank;
• drain hose.

The cause of the violation may not be directly related to the machine. It is recommended to check the sink (namely the siphon) and the drain pipe (sewer). Often they are the cause of clogging, which is why the spinning and draining do not work properly.

If this does not help, the reason may be related to the following elements:

1. The “No spin” option is turned on - then there is no malfunction, and there is no need to repair the Zanussi washing machine.
2. The regulator that turns off the spin does not work.
3. In rare cases, malfunction may occur due to damage to the motor or heating element. Then they should be replaced, but it is better to entrust such work to a professional.

Extraneous sounds

Extra sounds manifest themselves in the noisy operation of the engine. It can hum, although it does not rotate the drum. Then you should turn off the machine and replace the bearings that are already clearly worn out. They are sealed with oil seals, and if water penetrates under the oil seal, the bearing itself quickly breaks.

Do-it-yourself repair of a Zanussi washing machine can be done using the following algorithm:

1. Remove the plug from the socket.
2. Drain the liquid completely.
3. Remove all exterior panels.
4. Disconnect the drive belt from the tank, and also remove the remaining elements (spring, temperature sensor with pipes and counterweight).
5. Disconnect the pulley from the drum.
6. Take the bearings at the same time as the drum axis and separate them from each other.
7. Mount new bearings and install other elements.

In general, this is a sufficient measure, but noise can also be associated with other factors. For example, if an object gets stuck between the tank and the drum, then it needs to be removed. There may also be wear on the drive belt (it is replaced with another) or weak fixation of the pulley (the bolt is tightened by hand).

Electronics breakdowns

This is the most difficult case when repairing a Zanussi car with your own hands can only be done if you have the appropriate knowledge and at least minimal experience. For example, the violation is often associated with a burnt-out triac. It needs to be replaced, and the tracks on the electronic system module need to be soldered.

It also happens that the module itself fails. It is impossible to repair it - you will just have to replace the part. Usually an experienced craftsman is called in for this. Independent actions can lead to even greater damage.

Thus, in many cases, repairing a Zanussi washing machine with your own hands can be done independently. In most cases, it is enough to inspect the tank, as well as the hose and other components. But if this does not help or the electronics are broken, it is better not to risk it and invite a specialist.