Vestel washing machine: faults, step-by-step do-it-yourself repairs with photos

Some problems with the Vestel washing machine can be repaired yourself. For example, if you have the skills, you can tighten the belt, change it, or install a new heating element. However, for this you need to know the exact reason, taking into account what code appeared on the display or what indicators began to flash. A detailed description of the main codes and the procedure in different cases is presented in this article.

Basic error codes

If your Vestel washing machine displays error E01 or another message, you need to know exactly what it means. The main codes look like this:

1. E01 - indicates that the door is open or not tightly closed. Appears at the very beginning of washing - literally a few seconds after starting the program. It is necessary to check the mechanism that blocks the hatch.
2. E02 - unlike the first case, this error can also occur during the process, and the washing will continue. It is associated with improper filling of the tank (more water is poured than required). Similar Vestel error codes appear in case of low water pressure - you need to check whether the water supply is working properly. It may also turn out that the hose that fills the water or the electric valves are clogged.
3. If the “Ende” sign lights up during washing, such errors in the Vestel washing machine will cause the washing to stop.Then the water will be drained, and the spin will proceed at low speed (no more than 400 rpm). After an interrupted cycle, the message E03 will appear. It is necessary to check the drain hose or filter and clean them if necessary.
4. If code E04 appears, the wash will be interrupted, and the drain pump will begin to operate, draining the water. After a few minutes it turns off and starts working again. The reason is due to the incorrect operation of the electric water supply valve (it stops in the open position). Sometimes during washing the pressure in the water supply increases sharply. There is also a completely harmless reason when washing started with the water tap closed - it needs to be opened fully.
5. If error Vestel 01 appears at the very beginning of the washing process, then code E05 can appear at any time. It means that there is no water in the water supply. If it is, this indicates a malfunction of the sensor that monitors the liquid level. Problems may also be related to the electronic module.
6. There are other error codes for SMA Vestel, for example, E06. It warns of a malfunction of the drain pump or sensor that controls the liquid level.
7. If the message “E07” appears, it means that there is a water leak or the float sensor is broken.
8. E08 indicates failures in the electrical network, as well as voltage surges.
9. E09 - the control module has broken down, this is one of the most serious problems. You will need to repair the contacts or completely replace the board along with the processor. In extreme cases, the unit will simply stop turning on, or program failures and freezes will occur.
10. There are also error codes for the Vestel washing machine, which are designated E10. They indicate a problem with the engine or generator that senses engine speed.There may be no contact - then you need to inspect the internal components and make repairs.

You can determine error codes for Vestel washing machines without a display. For example, in the case of E02, 2 indicators are lit - 1 and 3. If it is necessary to report E03, lamps 1 and 4 are lit. If lamps 2 and 3 blink, this indicates E04. It also happens that you need to report a Vestel E01 error. Then the first and second indicators light up.

Most common faults

Most often, the following parts fail in different Vestel models:

1. Bearings that ensure smooth running of the drum. Because of this, the oil seal also wears out and loses its tightness. This can be determined externally by unusual noises, such as crackling, rumble or grinding.
2. Teng - then the water does not heat up, and the error codes issued by the Vestel WM 8341 may be different. A possible reason is severe overheating, the formation of scale and other deposits. The heating element needs to be cleaned or replaced, for which you will have to remove the panel from below.
3. The control module is broken - this causes a variety of malfunctions, the machine freezes and may not turn on at all. The possibility of self-repair is unlikely - it is better to contact an experienced technician, because the breakdown is quite serious.
4. The motor brushes wear out - they gradually wear out from constant contact with the motor commutator. Therefore, the drum rotates at a lower speed, the laundry is washed worse and remains quite damp.
5. Also, Vestel errors can lead to breakage or stretching of the belt that connects the engine to the drum. If it is severely worn, replacement is required.

Some of the described malfunctions can be corrected yourself.For example, the heating element can be cleaned with a solution of citric acid or replaced with a new one, having carefully studied the location of the wires (it is recommended to take a photo first). But there are also more serious breakdowns when do-it-yourself repairs not only will not help, but will also cause harm. In such cases, it is recommended to contact a qualified specialist.