Electrolux washing machine faults do-it-yourself repair

Repairing malfunctions of an Electrolux washing machine with your own hands is possible if the breakdown is not too serious, and also if you have the appropriate experience. As a rule, the drain system becomes clogged, the drum fails, or the unit does not turn on at all. Repair instructions for common situations can be found in this material.

If the car won't start

It happens that the unit does not turn on or freezes and does not respond to commands. In this case, do-it-yourself repair of an Electrolux washing machine is carried out as follows:

1. First you need to check the plug - how tightly it fits into the socket, and whether the contacts are burnt.
2. Next, check whether the outlet works.
3. If there has recently been a failure (voltage drop in the network), you need to turn off the device and wait a few minutes, and then plug it back in and start the program. This often helps if similar incidents have not been observed before.
4. The cause may be due to water or detergent getting on the control panel. Because of this, the keys stick and the contacts become damaged. Repairing an Electrolux top-loading washing machine in this case comes down to thoroughly removing moisture. If necessary, the panel will have to be disassembled and oxidized contacts replaced.

If this does not help, you should look for the cause in the network filter.Here the question arises of how to disassemble the Electrolux washing machine. The sequence of actions is as follows:

1. Remove the cover from above - to do this, unscrew the bolts shown in the photo.
2. Find a filter located near the wall. This may be the reason why the Electrolux washing machine does not turn on.
3. If there are defects in the form of scorched, burnt parts and swelling, the part definitely needs to be replaced. To do this, disconnect the wiring, remove the fasteners and tray to gain access to the keys.
4. Behind the control panel you can find buttons. They are pressed from the outside and taken out from the inside, then a new part is installed.

The door is jammed

Repair of a faulty Electrolux washing machine is also carried out in cases where the door cannot close tightly. Because of this, the wash does not start, so the device actually does not work. It is worth understanding that the door is equipped with a mechanical lock and an electronic one. The breakdown may be due to one or the other.

If the Electrolux washing machine does not start, you must proceed as follows:

1. Bend back the rubber cuff.
2. Remove the clamp by prying it off with a screwdriver.
3. Remove both screws.
4. Reach inside and remove the locking device.
5. If the Electrolux washing machine does not turn on, you should disconnect the contacts.
6. Install a new surge protector and then assemble all the parts in the opposite order.

Water does not flow in or drain out

Quite often there are malfunctions of the Electrolux washing machine associated with improper supply and drainage of water. For example, the liquid may not flow at all, or during one wash the unit collects and drains it several times. Then the corresponding error code, depending on the specific model, will light up on the display.

To find out the reason why the Electrolux washing machine does not work, and also to eliminate it, proceed as follows:

1. Close the tap, turn off the power to the device and disconnect the hose.
2. Behind it you can find a mesh filter, which is removed using pliers.
3. Then it must be rinsed under powerful water pressure to remove all contaminants. If necessary, manually remove large blockages and foreign objects. It will not be superfluous to disinfect the mesh with Domestos or another product.
4. The water supply hose is also cleaned. It can also become very clogged and become the reason why the Electrolux washing machine does not turn on.
5. Remove the top cover and find the inlet valve at the back wall.
6. Take a multimeter and check the contacts in resistance measurement mode. It should be from 2 to 4 ohms, otherwise the part will definitely not work.
7. Next, the fasteners and wiring are removed, after which a new valve is installed.

There are also cases of malfunction of the Electrolux top-loading washing machine, due to which it stopped, and water remained in the tank. Then you need to start cleaning the drain, proceeding like this:

1. Find the door under the loading hatch.
2. Open it, place the basin.
3. Unscrew the plastic outer part of the filter, moving counterclockwise.
4. Pull out the filter, remove debris and rinse under powerful water pressure.
5. Unfold the unit, remove the cover from the back and find the pump.
6. To troubleshoot an Electrolux washing machine, you will need to remove the screws located around the perimeter.
7. Next, loosen the clamps that secure the hose and pipe. All parts are cleaned.
8. The second end of the hose is also dismantled and washed under water pressure.
9. Inspect the pump and impeller especially carefully.It is cleaned of debris and foreign objects. If the engine burns out, which will be noticeable by the burning smell and characteristic marks, the part must be replaced.

The drum doesn't spin

When an Electrolux machine does not turn on, this may also be due to the fact that the drum does not rotate. The reasons can be both simpler and quite serious:

1. You need to remove the back panel and inspect the drum. Perhaps the belt has fallen off the pulley - it is installed back so that the tension is maximum (like a string).
2. Next, inspect the engine. Perhaps the brushes are worn out - they are dismantled and the contacts are removed. If at least one is worn out by more than half, both should be replaced. In this case, you will need to disassemble the Electrolux washing machine.
3. It is also recommended to ensure that there is no foreign object. To do this, remove the heating element by removing the nut and gently loosening it from side to side. Then they take a flashlight and shine it into the hole left after the heating element. It is there that a foreign object may be found, which is removed with tweezers.
4. The reason why the Electrolux washing machine does not turn on and the drum does not spin may be a breakdown of the tachometer. On the one hand, you need to make sure that it is properly secured and the contacts are intact. Next, the device is tested with a multimeter. If the resistance does not fall within the 60-70 Ohm range, the part must be replaced.

Thus, in order to carry out repairs correctly, it is important to know the structure of an Electrolux washing machine with a vertical loading or a regular front-loading one. To do this, you can use the presented diagram. Then you need to accurately determine the cause, and then carry out repairs. If this is not possible, contact a specialist.