Step-by-step instructions on how to disassemble an Indesit washing machine. Useful tips with photos

To carry out repairs or replace individual parts, it is necessary to disassemble the washing machine into its component parts. You need to act sequentially, removing the panels, disconnecting the wiring and other elements. Instructions on how to disassemble an Indesit washing machine with photos are presented in this material.

What you need for work

The preliminary stage begins with the preparation of tools and materials that will be needed for the work:

• a set of screwdrivers of different types, including bits in the form of hexagons and asterisks;
• keys of different types;
• disassembling the Indesit washing machine also involves using a hammer (if you plan to change the bearing);
• small wooden block;
• pliers;
• multimeter for measuring resistance and other parameters;
• pliers;
• WD-40 preparation (universal lubricant for corrosion protection).

The instructions on how to disassemble the Indesit washing machine also talk about preparing the device itself. It must be turned off, then remove the filter and place a basin to collect the remaining water. Next, you can begin the process itself.

Dismantling panels

First of all, the question arises of how to remove the front panel of the Indesit washing machine, as well as the back.It may be necessary to remove only one cover - it all depends on which element needs to be repaired. For example, to replace a heating element, only the front part is removed. If you need to replace the bearing, you will need to completely disassemble the Indesit washing machine yourself.

The step-by-step instructions are as follows:

1. First, remove the cover (the panel on top), which is secured with 2 bolts (they can be found at the back).
2. Next, pull the panel towards you and remove the cover manually, lifting it slightly.
3. The next step in how to disassemble an Indesit machine involves removing the panel at the back. It is large, so it is fixed with 6 bolts, each of which must be removed.
4. Now it's the turn of the front part. This is very easy to do, since the part is fixed with only 2 screws. Moreover, it does not need to be removed if there are no plans to repair the heating element or other elements located in front.
5. It is clear how to remove the bottom cover of the Indesit washing machine. It is easy to remove as it is held in place by 6 bolts. After this, remove the tray into which the powder product is poured. It is slightly lifted and pulled towards you, while simultaneously loosening it in both directions. In this case, you can see 3 screws, which should also be unscrewed.

Disabling communications

Next, disassembling the Indesit washing machine with your own hands involves disconnecting all the wires inside the case, as well as removing screws and other elements. The algorithm is like this:

1. Disconnect the wire that goes from the front panel to the control module (board with processor).
2. Dismantling the wires that connect to the powder receiver. There are blue and white wires here.To disassemble the Indesit washing machine correctly, you need to take a photo or remember where exactly a specific wire fits.
3. Next, you need to find the screw in the water supply area and unscrew it. A tube comes from the powder receiver, which is attached through a rubber eyelet. It is also removed by prying up this ear.
4. Disconnect the electrical cord. To properly disassemble the Indesit washing machine, you should find a part in the form of a rectangle - this is where the cord is attached. The screw is unscrewed and then pulled up.
5. It is also necessary to remove the rubber band that is secured by a spring between the hatch and the tank. To dismantle it, press on it and pull it up.

Dismantling the heating element

The next stage of the instructions on how to disassemble the Indesit automatic machine involves dismantling the heating element. It is easy to find behind the back cover. At the same time, the removal itself may seem difficult, but in fact the main thing is to carefully act in the following sequence:

1. Open a small panel below the loading hatch.
2. Find the filter plug and unscrew it, moving counterclockwise.
3. If necessary, place a basin so that the remaining water gets into it.
4. Remove the water supply hose.
5. The drain hose is also dismantled.
6. Now you need to understand how the Indesit washing machine, namely the heating element, is disassembled. First, it is photographed so that later the wires can be connected correctly.
7. Next, disconnect the wires from the connectors, bend the tab and unfasten the wires from the temperature sensor.
8. To get the heating element, loosen the fastening and remove the nut in the center (but not to the very end). The bolt is pressed inward and the heating element is carefully pryed off using a flat-head screwdriver.
9. Disassembling the Indesit washing machine at this stage can be difficult, since here you need to carefully swing the heating element from side to side.
10. If necessary, install a new heating element, after which the Indesit washing machine is reassembled in the reverse order.

Removing the tank

The next step on how to disassemble an Indesit washing machine comes down to dismantling the tank. The instructions look like this:

1. The unit is turned over and placed on its “head”. Moreover, it is better not perpendicularly, but diagonally, that is, at approximately an angle of 45°.
2. To properly disassemble the Indesit washing machine, remove the bolts on the left and right to which the shock absorbers are fixed.
3. Place the car again in its normal position, that is, on the bottom.
4. Remove the tank made of plastic. The instructions on how to disassemble the Indesit washing machine recommend working with two people at this stage, since the springs also need to be removed.
5. Open the hatch cover and keep it open all the time.
6. Dismantle the shock absorbers, which are attached to the tank using plastic pins.
7. Remove the motor and rubber pipe.
8. Finally, the load from below is removed.

How to remove the tank

You need to understand that disassembling the Indesit WITL 867 and other models actually ends here, because the tank itself is non-dismountable, so if it breaks, it is not repaired, but replaced with a new one. To extract it, proceed as follows:

1. Take a thin drill and make holes in the end part of the seam, moving along the entire circumference (it is recommended to retreat 15 cm).
2. Take a larger drill and again go through the holes already made to widen them.
3. Next, disassembling the Indesit machine comes down to placing the tank vertically on a flat surface and sawing the factory seam. To do this you will need a hacksaw for metal work.Sawing proceeds very slowly, at least 3 hours, since the work must be done very carefully. Otherwise, due to incorrect movements, it will no longer be possible to glue the tank.

Thus, disassembling the Indesit washing machine requires certain skills, especially in cases where the process needs to be completed to the very end and the tank removed. It is first recommended to understand the diagram of a specific model in order to correctly outline the sequence of actions. Disassembled parts are tested for operability and clogging, and if necessary, they are replaced with new spare parts.