Why does error e3 occur in a Gorenje washing machine? Ways to find a breakdown and fix it

Error E3 in a Gorenje washing machine appears in situations where the water drainage system fails. The easiest way to diagnose is to make sure that the pressure in the water supply is normal, inspect the hose, open the tap, and clean the filter mesh. But it also happens that the reasons are related to electronics, and then you cannot do without consulting an experienced specialist.

Reasons for appearance

The Gorenje washing machine diagnoses error E3 in different cases. They are mainly due to the fact that the operation of the drain hose or other elements is disrupted, although there may be other options. Among them we can consider the most common ones:

1. The Gorenje washing machine shows error E3 if the water supply from the water supply is poor. In this case, the reason may not be related to the device itself. You need to check whether the tap is open and whether there is sufficient pressure in the water supply. If everything is in order, it is recommended to inspect the hose for kinks and kinks.
2. Error F3 of the Gorenje washing machine also appears due to failures associated with the parts responsible for draining. It happens, for example, that the connection to the sewer is not made correctly, and the water that entered the machine immediately goes back into the pipe. Therefore, you will constantly hear how the liquid is drained, but the water is not collected.
3. If there is a leak, the Gorenje washing machine will display error 7, and the process does not proceed because the required volume of water is not collected. You can verify this reason by seeing leaking water next to the unit.
4. If the display shows error F4 in a Gorenje or E3 washing machine, this may also be due to a situation such as a failure of the sensor that determines the volume of incoming liquid. The device transmits incorrect data to the control module, so the machine cannot start the washing process.
5. Finally, there may be a factor such as a malfunction of the control module. Then the unit may freeze and even stop responding to commands or turning on.

Error E7 washing machine Burning, E3 and other common faults can be eliminated independently if you accurately determine the cause. To do this, you need to focus both on the codes on the display and on external signs.

There is no water or it does not pass through

When a Gorenje washing machine shows error F7, this often indicates problems with water supply. To carry out self-diagnosis, it is recommended to proceed as follows:

1. Make sure there is water in the tap.
2. Open the cold water supply tap fully.
3. Remove the plug from the socket and turn off the water.
4. If there is error 03 in the Gorenje washing machine, you need to unscrew the water supply hose by loosening the clamps attached to the body.
5. Clamp the filter using pliers or pliers and pull it towards you.
6. Clean the mesh using tweezers and rinse under strong water pressure.
7. If this doesn’t help, dissolve 2 tablespoons of citric acid in a glass of water and pour into the mesh for an hour.
8. After this, all the parts are put in place - the Gorenye washing machine will no longer show error 4.

Intake valve malfunction

There is another reason why the Gorenje washing machine shows error 3. It is related to the inlet valve. This is a small but important unit; you can find it under the top cover (located next to the back panel).

After detection, you need to check the part so that the Gorenje washing machine does not show error F4 or E3. To do this, take a multimeter and act like this:

1. Set up the device to measure resistance (in Ohms).
2. Attach the probes to the windings.
3. See the number on the display. If the valve is single-coil, the value will be approximately 3.8 kOhm, but if there are 2 or 3 coils, the number should be in the range of 2-4 kOhm.
4. If the element is faulty, you need to photograph it to clarify the order in which the different wires are connected, and dismantle it.
5. Then you need to install a new part, screwing it to the wall and then connecting all the necessary wires, focusing on the previously taken photograph. After this, the Gorenje washing machine will not show error E3.

Breakdown of the pressure switch

Error codes for Gorenje washing machines clearly indicate the specific cause of the failure. In the case of E3, you need to know not only the decryption, but also the features of its appearance. If this happened for the first time, most likely the pressure switch that controls the liquid level has broken. To check and repair it, proceed as follows:

1. Remove the top cover.
2. Next you need to see a disk from which a rather long tube goes towards the tank.
3. Find a disk to which a long tube leading into the tank is attached.
4. To prevent the Gorenje washing machine from showing error F3, this part must be removed.
5. Blow and find a tube with a diameter corresponding to the fitting. It must be inserted into the appropriate connector.
6. You need to blow weakly again and listen for any clicks.If yes, then the part works; if not, it is broken.
7. Next you need to ring all the remaining contacts in resistance mode. If the reading fluctuates within a small range, this is normal.
8. If there is no resistance, this is an obvious malfunction of the Gorenye washing machine. Then the burnt or damaged contacts are replaced with new ones.

But it also happens that all sensors work normally, there are no damaged areas. At the same time, the error code F7 Gorenje still appears on the display, then the failure is associated with the control board. Most likely, the failure is observed only on one triac, so incorrect data on the liquid level is received, which is why the process does not start.

Moreover, it may turn out that the Gorenje washing machine does not turn on, freezes, or all programs are lost. Then independent repairs are not allowed, as it can lead to serious damage. If the Gorenye washing machine shows error F4 and does not work correctly, it is better to call a technician who can identify the exact cause of the failure and fix it.

Thus, the Gorenje washing machine may produce error 4 and other codes. In the case of common E3, the cause is most often associated with different nodes responsible for draining. By eliminating certain factors step by step, you can detect the breakdown of a specific spare part and begin to repair it.