Why does the Kandy washing machine display error E03? When does it occur and how can it be eliminated?

If the Kandy washing machine shows error E03, the reason is related to the drain - the waste water either does not leave at all or flows too slowly. In the simplest cases, the cause is due to a clogged drain hose, filter, or the sewer itself. But there are also more complex situations, which are described in detail in this article.

Causes of malfunction

If code E03 appears on the display, this indicates problems with the drainage system. The water may drain too slowly or not come out at all. Although often the cause may not even be the drain itself (clogging, improper installation), but also a breakdown in the heating circuit.

At the same time, the Candy washing machine shows error e03 in different ways, most often users encounter the following situations:

1. During the washing process or while operating in the rinsing mode, the unit normally drains waste water, but still shows the Kandy display error e03.
2. After this message appears, the plugs on the meter are knocked out, and the entire apartment is de-energized.
3. The device displays a code and does not heat the water, which makes normal washing impossible. You can verify this by touching the glass of the door - it will be noticeably cool.
4. Error E03 in a washing machine can alternate with fault E16. In this case, the water will also stop heating.

How is the error indicated on different models?

You need to understand that E03 error in the Candy washing machine is a standard designation that is displayed on the display of most models. Some devices may have other codes:

• E3;
• Error 3;
• Err 3 (abbreviated).

However, the common thing is that the code always contains the number 3, so it is intuitively clear what exactly was meant.

If the unit is not equipped with a display, error e03 issued by Candy will be indicated by flashing 3 indicators. The user will see 3 light signals, then there will be a pause of a few seconds, and then 3 flashes will appear again. Moreover, the combinations of light indicators can be different:

1. An intense arrow icon combined with the first light bulb from the left.
2. An intense arrow icon in the combination of the upper light bulb in the place where the countdown to the end of the wash is indicated.
3. Cold water wash option (snowflake icon).

Is it possible to repair it yourself?

If Candy shows error e03, eliminating it at home is quite possible. Since most often the cause is associated with a clogged water drainage system, you need to act like this:

1. First, check the drain hose for kinks and deformations. If it is crushed by any object, a wall, the water will go worse. Then you need to carefully move the hose and, if necessary, move the unit itself a little.
2. Next, check the drain filter. It periodically becomes clogged due to small debris and lint from the surface of clothing, as a result of which the drain may be completely blocked. To repair, the filter is unscrewed and thoroughly cleaned.If it is in too bad condition, it is better to replace it with a new part. After the repair, the error e03 previously shown by Candy should disappear.
3. A blockage where the drain enters the sewer (usually a siphon under the sink). To check, you need to disconnect the drain hose and direct the free end into the toilet. Next, they start the wash, and if the drainage goes well, it means that the sewer pipe really needs to be cleaned.
4. Another reason may be due to a system failure. The fact is that due to voltage fluctuations or natural wear and tear, the electronic module with the processor stops working normally. If this is an isolated case, it is recommended to simply unplug the plug from the socket, wait 15 minutes and turn it on again. The same method is used when the Kandy washing machine shows error E07.

When is professional repair needed?

If all the described methods did not help, and the same message appears on the display again, the reason is due to a more serious failure. Such situations require professional diagnosis and repair, before which the device cannot be used.

The most common cases include:

1. The drain pump is broken - in this case, the machine will stop draining water even in slow mode.
2. The control unit has broken down, which may be due to a general system failure. In such cases, other messages may light up on the display. For example, the Kandy washing machine will show error e01. It indicates that the door is not fully closed. Although in fact everything may be in order with the lock, it is the electronics (control module) that is not working.
3. If the unit begins to electrocute, and code E03 appears after washing, for example, during a spin cycle, this indicates problems with the heating element, i.e. tena. This malfunction is dangerous, so the machine is no longer used until professional repairs are completed.
4. The control unit has stopped working. In this case, the water will not drain, and the wash itself may stop at the rinsing stage or during the spin cycle.
5. The pressure switch has broken down - most often this happens due to contamination of the sampling chamber, a blockage in the hose, or a malfunction on the sensor side of the unit.
6. The contacts in the electrical circuit or the wiring itself are damaged. Then the current flows through the body and hits noticeably.
7. Finally, the message may appear due to the fact that the insulation in the pads is broken. Then the unit will also receive an electric shock, and the drum will begin to rotate poorly while operating in spin mode.

Thus, by showing error e03, the Kandy washing machine warns the user of a malfunction in the drain system. But it is not always possible to establish the exact cause. Therefore, if you are not sure or the repair involves replacing complex parts, it is better to contact a specialist. Fixing the problem yourself without the necessary skills can lead to even greater damage.