What malfunctions does the Veko washing machine (5 kg) have: ways to eliminate them, step-by-step repairs

Malfunctions of the Veko 5 kg washing machine are mainly related to the drainage system, water supply, heating, and also to the drum. More serious damage to electronics may also occur. In some cases, you can carry out independent repairs. A description of the main breakdowns and how to fix them can be found in this article.

Main types of faults

If the Veko washing machine does not turn on, you need to look for the reasons immediately. They can indicate either a relatively simple or complex breakdown. Moreover, the unit often starts, but the washing process fails, the laundry remains wet, or other problems appear. The most common situations are:

1. The water remains cool and the clothes are practically not washed.
2. The Veko washing machine does not start, or it turns on, but the water flows very slowly (it may not even fill at all).
3. It also happens that the Veko washing machine does not turn on or the washing process does not start due to the door not being closed well enough.
4. When a Veko washing machine does not work, the reason may also be related to drainage problems - the water does not drain well or does not drain at all, which is why the tank remains full.
5. Another case when the Beko washing machine does not start is due to a voltage drop in the network.Because of this, the electronics may suffer; in the most difficult cases, you will have to restore the contacts on the board or change the entire control module.
6. Also, the Beko washing machine does not turn on due to the fact that the drum or bearings or seal are broken. It may not rotate at all, or it may rotate with extraneous noise, grinding noises, and even rumbles.
7. When the Beko washing machine does not turn on, all the lights on the panel may blink. Or the program starts as usual, but in fact the washing does not proceed. In this case, the problem is most likely related to the electronics.
8. If you cannot start the machine using the button (in normal mode), this indicates a malfunction of the Beko washing machine. The electronics or power cord may have been damaged.

The following describes the most common malfunctions, their causes, as well as recommendations for repairs.

Problems with drainage

If the Veko washing machine does not start, this may be due to problems with the drain system. Most often, the drain filter breaks, which cleans the water from lint, dust and other contaminants. You can determine its location quite quickly - the filter is installed at the very bottom of the front panel. Moreover, there is a special door installed for it that needs to be opened.

In this case, repairs to the Veko washing machine are done with your own hands. The instructions are:

1. Place a basin and prepare a rag. Take out the filter by first turning it to the right. Next, it is cleaned and washed under running water.
2. Take a screwdriver and clean the pipe, which can also become clogged over time.
3. To avoid malfunction of the Veko washing machine, it is also recommended to clean the filter that purifies the incoming water.It can be found at the back, in the place where the hose is attached.
4. After cleaning the inlet filter, install it in place and continue repairing the Beko washing machine with your own hands. Now you need to check the drain pump, which may also be damaged by contamination. Quite often, the unit itself detects the malfunction and displays error H5 on the display. It can also be identified by the hum when water is supplied.
5. To check the pump, you need to determine the reasons why the Beko washing machine does not turn on. To do this, remove the plug from the socket and reinsert it after 15 minutes. If the device is working, start the drain and inspect the plug hole to make sure that the impeller is working properly. Otherwise, you will need to clean or replace the pump.

Water does not heat up

During the washing process, not only valves and filters become clogged, but also the heating element. If the Veko washing machine breaks down, it will be noticeable by the fact that the water does not heat up, and therefore the clothes are not washed.

Often the heating element becomes clogged with scale or simply wears out. As a result, it can overheat greatly, causing a burning smell. In advanced cases, a short circuit may even occur.

To replace the heating element, you need to determine its location. Usually, when a Veko washing machine breaks down, they look for the heating element from the front. To do this, you will have to remove the cuff, as shown in the photo.

Then proceed like this:

1. They find the heating element - you can’t see it entirely, only the tail part with the wires going to it is accessible. Each of them needs to be disconnected.
2. Take a multimeter and switch it to resistance measurement mode.If the indicator does not correspond to the range from 25 to 30 Ohms, then a breakdown has clearly occurred.
3. Remove the heating element by removing the central nut. Thoroughly clean the place of its attachment from contamination.
4. Then they put in a new part and assemble all the elements, moving in the reverse order.

If the heating element is not broken, you need to check the sensor that measures the temperature. Most likely, the reasons for the breakdown of the Veko washing machine are related to it. The algorithm is as follows:

1. Remove the cover from above by unscrewing the bolts.
2. Carefully remove the tray into which the powder is poured.
3. Find the sensor and disconnect each wire.
4. Next, the resistance is measured - if it does not correspond to 4.7 kOhm, the part has failed.
5. You can also heat the sensor in a container of warm water. If the voltage does not decrease, this also indicates a breakdown.
6. Since the operation of the Veko washing machine takes quite a long time, the broken part must be replaced with a new one and then put everything back together.

There may be more serious malfunctions of the Veko washing machine. For example, if the drum is loose and rotates with a grinding noise, the oil seal and bearings need to be replaced. This is easy to do, but you will first need to disassemble the entire unit to get to the necessary parts.

Also, breakdowns of the Veko washing machine can be associated with electronics. When there is a voltage drop in the network or droplets of moisture get on the board, this will most likely lead to the failure of individual contacts. They are soldered or a new control module is installed. It is quite difficult to fix such malfunctions of the Veko 6 kg washing machine yourself - it is better to call a specialist.