Which Ariston washing machine has faults and how to fix them. Instructions for use

Ariston washing machines are distinguished by high-quality assembly, so they serve without complaints for several years in a row. But sometimes failures occur, and the reasons can be quite simple or complex. The main malfunctions of the Ariston washing machine and their elimination are described in detail in this article.

Heating element malfunctions

The heating element is the weak point of any machine in the sense that as it wears out, it inevitably becomes clogged with scale, like, for example, the heating element of a kettle. Due to the fact that the surface is covered with plaque and the layer gradually increases, the water begins to heat up worse.

As a result, the heating element heats up more, and if the blockage is quite severe, this can lead to combustion and even a short circuit. The main symptom is that the water does not heat up or remains quite cool. This is easy to understand by touching the door with your hand while washing.

A faulty heating element definitely needs to be replaced. If the element is fully functional, it is enough to clean it. In any case, you will need to remove it from the car, the sequence of actions is as follows:

1. Be sure to disconnect the unit from the network and turn off the tap.
2. Next, remove the hoses that supply and discharge water.
3. Remove the back panel; to do this, simply unscrew the screws or bolts.
4. Remove the heating element wires.It’s better to take pictures of them right away, so that you can later understand how to place them correctly for a new element.
5. Loosen the nut (it should only hold at the end of the thread).
6. Press the nut inward along with the stud.
7. Now you can take out the heating element and clean it or replace it with a new one. If the element is operational, cleaning is carried out using citric acid or a special product, for example, Antikipin.

Electronics malfunctions

The Ariston washing machine also has faults related to the electronics, or more precisely, to the control module. This is one of the most serious failures because it often requires replacing the processor board, which can be quite expensive.

However, the failure can also be one-time, for example, after a power surge. Then just unplug the plug and wait 15-20 minutes. Then, if the current is supplied stably, you need to reinsert the plug and check how the device works.

If the Ariston washing machine does not turn on, the programs fail or the drum does not rotate, this clearly indicates problems in the electronic board. Moreover, errors with code F09 or F12 may appear on the display. If there is no screen, different indicators will start blinking.

In most cases, this problem cannot be eliminated. Therefore, it is recommended to contact a service center. A specialist must accurately diagnose the cause, solder the tracks that burned out due to a failure, replace the relay and other radio elements. In some cases, a complete replacement of the board will be required. Thanks to this, the reasons why the Ariston washing machine does not turn on will be eliminated.

Pump failure

Quite often the pump on the machine breaks down. This is due to disturbances in the operation of the engine and pump.It may also happen that foreign objects got into this element, causing the impeller to break. In such cases, the device will stop draining water, the indicators will begin to blink, and if there is a display, errors with codes F05 or F11 will appear.

To replace, you need to buy a new part, the sequence of actions is as follows:

1. Disconnect the plug from the socket.
2. Drain the water using the emergency drain system.
3. Close the tap.
4. Tilt the machine towards you by placing a rag under it or lay it on its left side.
5. The pump is freely accessible - it can be removed by unscrewing each screw in sequence.
6. Press down on the element from the side where the drain valve is located.
7. Pull the housing towards you and drain the excess liquid.
8. Pry off the latch located on the pump body on both sides.
9. Remove the pump from the reel.
10. Install the new part in reverse order.

If the unit is faulty, you first need to determine the cause. For example, when the Ariston Hotpoint washing machine does not turn on, most likely this is due to the electronic control unit, and if the water does not heat up well, the heating element is broken. You can replace or repair parts yourself, but if you have little experience, it is better to contact a qualified specialist.