How to remove the drum from an Indesit washing machine? Do-it-yourself tank repairs

In some cases, the washing machine drum needs to be replaced, or at least repaired (replacement of the oil seal and bearings). To do this, you need to figure out how to remove the drum from the Indesit washing machine, as well as how to install a new part. Step-by-step instructions with photos and descriptions of each action are presented in this article.

Preparatory work

Replacing the drum in an Indesit washing machine begins with preparing the necessary tools. You will need improvised devices that can be found in any home:

• flat and figured screwdrivers;
• set of wrenches;
• mites;
• pliers;
• hammer;
• wire cutters.

During work, the question may arise about how to cut the drum of an Indesit washing machine. On some models it is collapsible, on others it is not. Therefore, it is better to stock up on a chisel and a hacksaw for metal. The device is first disconnected from the network, but it would still be better to stock up on insulated tools.

Step-by-step replacement instructions

Repairing the drum of an Indesit washing machine is carried out in stages, and it is recommended to prepare a phone with a good camera, as well as a flashlight. The internal structure should first be photographed from different sides, so that later you can easily put the parts in place after disassembling the drum.

In addition, this will allow you to understand how to open the bottom cover of the Indesit washing machine, where what fasteners are installed, etc. It will not be superfluous to familiarize yourself with the structure of the unit. To do this, you can study the presented diagram.

Step-by-step replacement instructions look like this:

1. Unscrew each bolt on the back cover.
2. To get to the drum and understand how to cut the tank of an Indesit washing machine, you should also remove the top panel.
3. Now you need to remove the tray into which the powder product is poured, and also unscrew the 2 bolts on the right and left, as shown in the photo. This is necessary in order to remove the front panel - otherwise it will interfere with work.
4. Unscrew the bolts and remove the insert shown in the photo (in the upper right corner).
5. Replacing the tank in an Indesit washing machine is impossible without removing the cuff. It is necessary to pry up the rubber seal with a screwdriver and carefully remove it so as not to tear it.
6. Disconnect motor terminals.
7. Also remove the pump contacts.
8. Next you need to understand how to disassemble the drum motor. But first you should remove the heating element.
9. Now it’s clear how to remove the rubber band and how to remove the cuvette from the Indesit washing machine. The next stage involves dismantling the shock absorbers. To do this, unscrew the bolts in the center from the top and bottom.
10. Before removing the drum of the Indesit washing machine, you need to clamp the hose clamp with pliers and pull it out.
11. Turn the unit over and remove the small clamp and hose.
12. Now you can easily remove the old part, and then the installation of the drum on the Indesit washing machine begins.
13. First, 2 pipes are removed from the old part - one is removed manually, and the bolt of the second needs to be unscrewed. To do this, you need to understand how the drum is attached to the Indesit washing machine.
14. Then the hose is dismantled. It is also attached to a clamp, which is easy to remove.
15. The new drum is equipped with pipes and other elements from the old one. If necessary, they must be cleaned first. If they are very worn, it is better to immediately replace them with new ones.
16. Now it’s clear how to change the drum in an Indesit washing machine - install a new part and collect all the spare parts, moving in the reverse order.

Replacing bearings

Repairing the drum of an Indesit washing machine with your own hands often requires replacing the bearings and oil seal, which inevitably wear out over time. The installation of new spare parts itself is not difficult, but to do this you have to disassemble the drum, i.e. basically the whole car. Therefore, it is better to immediately install all new parts, even if one or two of them are not worn out.

It is quite simple to understand that a breakdown of these elements has occurred - there are several reliable signs for this:

1. If you open the door and press the drum so that it goes up, there should be no movement - otherwise the bearings will definitely wear out.
2. You can also look at the unit from the reverse side. To do this, you need to follow the instructions on how to remove the drum from the Indesit washing machine. If there are visible leaks under the pulley, this is also a sign that the bearings need to be urgently replaced.
3. There are also other “symptoms”, to determine which it is not necessary to disassemble the unit and repair the tank of the Indesit washing machine. For example, the laundry does not spin well, the tank sways a lot, and extraneous noise appears during the spin cycle.

To replace, you need to disassemble the unit, remove the nut from the center of the drum shaft, and then remove the cover and pull out the oil seal using a chisel or straight screwdriver.Similarly, remove both bearings and replace all parts.

It is clear that in some cases the question may arise about how to cut the drum of a washing machine. To do this, use a hacksaw or grinder. You can also use an electric jigsaw, chain saw, or even a drill. Although if you only need to replace the tank, you no longer need to do this - the old part is simply thrown away or sold at a symbolic price.

Thus, it is quite possible to repair the Indesit drum yourself. This is a rather labor-intensive process that requires a little skill and understanding of the washing machine, i.e. its structure, the location of each element. On the other hand, doing it yourself only takes 1-2 hours and saves a lot of money. Therefore, it’s definitely worth trying to do it yourself.