How to disassemble a Bosch washing machine? Step-by-step algorithm for repairing a washing machine

It is not difficult to understand how to disassemble a Bosch washing machine - all steps are performed in stages, using screwdrivers, keys, a hammer and a chisel. In some cases, you may also need WD40, which is best purchased in advance. Step-by-step instructions for dismantling all elements of the device with photos and descriptions of actions can be found in the presented material.

Preparatory work

Before disassembling the Bosch washing machine, you need to understand its structure. This is important in order to understand where each part is located (for example, the heating element is located under the tank in front, and not in the back).

The dismantling process takes place in several stages - first, all panels are removed, including controls, as well as the tray for adding powder. After this, disassembling the Bosch washing machine comes down to the step-by-step removal of each part. For work, prepare a basin, a rag, as well as available tools:

• a set of screwdrivers (including slotted ones);
• set of hexagons;
• hammer;
• pliers;
• wire cutters;
• Torx;
• bit.

You also need to turn off the device from the network in advance, close the tap, and, if necessary, drain the water from the inlet hose. It is unscrewed and the free end is directed into the pelvis. The unit must be placed conveniently so that there is access from each side.Next, you can begin to study the instructions on how to disassemble a Bosch washing machine.

Dismantling panels

The dismantling process takes place in several stages, and first you need to remove all the panels. The sequence of actions is as follows:

1. Open the door and remove it from its hinges, removing each screw. You need to work carefully at this stage so as not to scratch the glass.
2. Next, bend the cuff and remove the clamp. You can pry it with a screwdriver and pull it off. The rubber seal itself is tucked inside the drum.
3. Then disassembling the Bosch washing machine comes down to removing the bolts that secure the lock. To do this, you need to get the device that blocks the hatch - put your hand behind the body and remove the mechanism. There are several wires going to it - they are also disconnected.
4. Unscrew the screws that run along the front of the panel and remove the cover.
5. After this, remove the panel from behind, unscrewing each bolt along the perimeter. Behind the panel you can see all the main parts, as well as counterweights. These are the heaviest blocks (made of concrete) that also need to be removed. They are unscrewed with a 14 key.

Removing internal parts

Then the disassembly of the Bosch washing machine moves to a new stage - you need to get to the tank. But to do this, first remove all the elements that are fixed to it from different sides. The instructions are:

1. Remove the dispenser tray and dismantle the pipe that leads to it. If there is a clamp, loosen it using pliers. At the same time, you need to remove the pipe from the inlet valve.
2. Next, remove the sensor that controls the water level (pressure switch) and the filter. To do this, remove the wiring and unscrew the bolts that secure these units. A tube fits to the pressure switch - it also needs to be removed.
3. Now you can understand how to disassemble a Bosch washing machine from the back. First, remove the drive belt from the pulley. It is very tight and requires a lot of force.
4. Disconnect the wires that go to the electric motor.
5. Unscrew the bolts that hold the motor in place.
6. By rocking the engine slightly to the right and left, it can be removed from the housing. You need to be prepared for the fact that the element is very heavy - it will require effort.
7. The next step in the instructions on how to disassemble a Bosch washing machine involves removing the pump. The unit is placed on the left side and the bottom is removed (some models do not have it). To do this, you need to unscrew each bolt.
8. Using pliers, remove the clamp that secures the drain pipe and dismantle the part. Residues of waste liquid may accumulate in it, so you need to place a rag.
9. Unclench the wires that lead to the pump and unscrew the bolts that secure the drain pump.

Removing the tank and disassembling the drum

Let's disassemble the Bosch washing machine further. The advantage of models from this manufacturer is that the tank is collapsible. Therefore, all that remains is to remove it and get to the drum. The algorithm of actions is as follows:

1. Disconnect the pulley. To prevent it from rotating, install a support or other clamp. Unscrew the bolt located in the center. At first it may not give in - then you can use WD40.
2. Remove the bolts along the perimeter that secure both halves.
3. Next, remove the top part - it should turn out approximately the same as shown in the photo.
4. The tank is turned over and, tapping the rod with a small hammer, the base, that is, the drum, is removed.
5. Then, if necessary, you can remove the bearing and remove the seals - if they are worn out, it is better to replace the parts completely, even if some part looks new.
6. Place the chisel on the bearing, as shown in the photo, and knock it out with a hammer, moving in a circle.

From these instructions it is quite clear how to remove the top cover of a Bosch washing machine and remove other panels and internal parts. It is quite possible to dismantle them yourself. Difficulties can only arise when disassembling the engine or tank. But if you understand how to disassemble a Bosch washing machine, you can handle these parts.