How is the bearing replaced in an Ariston washing machine? DIY washing machine repair

Replacing a bearing in an Ariston washing machine is a rather labor-intensive operation that requires certain skills, available tools and space. The fact is that the bearings are located under the drum, and to get to them, you have to disassemble almost the entire unit. How to do this correctly is described in detail in the presented material.

When replacement is required

Before you understand how to change the bearing on an Ariston washing machine, you should understand the diagnostic rules. Normally, this part wears out earlier than after 5-6 years of constant use. Often the service life reaches even 10 years.

But if you constantly overload the drum, the seal will lose its seal, so water will get on the bearing and the lubricant will begin to wash out. All this leads to premature wear of the part, for example, after 3-4 years. Breakage can occur in the first year of use due to manufacturing defects. But such cases are very rare.

Replacing the Hotpoint Ariston bearing is required when the following symptoms are observed:

• strong vibration, noise during spin mode;
• rocking of the drum (if you move it with your hand in a calm state);
• uneven rotation of the drum (you also need to move it by hand);
• damage to the edges of the cuff;
• poor spinning of laundry, even if the drum is not fully loaded, for example, half.

It is best to replace a Hotpoint Ariston bearing as quickly as possible. Otherwise, the drum itself may break, and such repairs are more labor-intensive and cost more. If in doubt, it is better to call an experienced technician for diagnosis and restoration work.

Preparing for replacement

Replacing a bearing in a Hotpoint Ariston washing machine requires first purchasing an original part from a trusted store. Moreover, it is necessary to take not only the bearing itself, but also the oil seal. Replacement is carried out at the same time, because otherwise the old part will begin to wear out the new one, and literally in a few months or a year another repair will be needed.

Before starting work, you need to study the instructions on how to replace the bearing in an Ariston washing machine, as well as prepare the available tools and materials:

• a set of screwdrivers of different types;
• in some cases, wire cutters will be required;
• regular hammer;
• pliers are definitely needed;
• socket type wrenches (set);
• bit;
• glue;
• puller (optional);
• WD-40 liquid;
• pelvis

It is also important to make sure that there is enough space for repairs, because the car will have to be almost completely disassembled and turned on different sides. It is better to remove all furniture and other items, or, as a last resort, do the work in another place, for example, in the garage.

Disassembling the machine

Replacing the drum bearing of an Ariston washing machine begins with turning off the unit, removing the plug from the network, and also turning off the cold water tap. The hose is also disconnected from the entry point into the housing and suspended. Place a basin in advance and allow the water to drain completely.

Next, the replacement of the Ariston ARSL 85 bearing or another model begins, the main steps are as follows:

1. They find a hatch at the bottom and open it by removing the latches. Remove the drain filter, place a small container again, and place a rag to drain the water.
2. Pull out the unit so that you can access the panel from behind. Remove the 2 bolts that secure the top panel. They move it forward and dismantle it.
3. To install a new drum bearing for the Ariston washing machine, remove the panel from the back. Moreover, to do this you will need to unscrew each screw sequentially. You also need to remove the drive belt if the unit is equipped with one. Manually rotate the pulley and pull the belt towards you.
4. They go to the front side again and remove the tray, where they pour the powder and pour in the conditioner. They simply pull it towards themselves and press the latch, which is located in the middle. Remove the bolts behind the retainer and disconnect the plastic latches. The panel will remain attached to the wires, as can be seen in the photo - they should not be removed, it’s easier to leave them as they are.
5. Replacing an Ariston AVSL 109 or another model bearing itself is a simple operation. But its labor intensity is associated with preliminary preparation, namely, the dismantling of other parts that interfere with getting to the main part. It will be necessary, for example, to remove the powder receptacle by loosening the tension on the pipe. It is also removed and the valve contacts are disconnected.
6. Unscrew the screws that secure the lock blocking the hatch.
7. If there is a risk of damage to the sunroof glass, it is also better to remove it along with the door, removing the corresponding fastener.
8. At the bottom of the tank, the wiring going to the electric motor is removed. This is one of the last steps before replacing the Hotpoint Ariston drum bearing begins.If necessary, cut the clamps using wire cutters and move the bundle of wires further away so that it does not interfere.
9. Unscrew the screws that secure the shock absorbers and carefully remove the drum with a hook.

Replacing bearings

The disassembly stage is completed - all that remains is to actually replace the worn elements. You should proceed like this:

1. Remove the pulley. It is stopped with a stick and then the central bolt is unscrewed. If it is very difficult, it is treated with WD-40.
2. Once the pulley is removed, you can disassemble the tank. To do this, unscrew each bolt, moving sequentially. Then the latches are removed and the upper half is disconnected.
3. Gently hit the bushing with a hammer until the drum flies out.
4. The tank is turned over and placed with the outer half facing you. Place a chisel on the surface of the holder and hit it with a hammer. The inner bearing is removed in the same way. If there is a special device = puller, the work will be easier.
5. Install new bearings, first cleaning the area with WD-40 and removing any remaining dirt. An oil seal is placed on top.
6. Clean the bushing from traces of rusty deposits and only after that put the drum in place.

Now it’s clear how to change the bearing on an Ariston washing machine. After installing the new elements, connect all the parts, moving in the reverse order. Then you can spin the drum a little to check how evenly it moves.