How is the bearing replaced in an Ariston washing machine? DIY washing machine repair
Replacing the bearing in an Ariston washing machine is necessary for every device after long-term use. If the drum begins to rotate with a clanging sound and does not wring out things well, this indicates the need for urgent repairs. You can do it yourself - how to do this is described in detail in the article.
The content of the article
Causes and signs of failure
Before you figure out how to change the bearing on an Ariston washing machine, you need to make sure that it is the bearing that is faulty. Bearings break due to natural wear and tear, which occurs after several years of relatively intensive washing.
You will have to use the instructions on how to change the bearing on an Ariston washing machine when the following signs are noticeable:
- During washing or rinsing, extraneous sounds appear, for example, the grinding of metal surfaces or knocking. They also appear during spinning, but are hardly noticeable due to the general noise.
- The quality of the spin cycle has noticeably deteriorated; the laundry remains damp, even if there is not much of it in the machine.
- Replacing the Hotpoint Ariston bearing is also required in cases where the unit has clearly begun to sway too much. This is not so easy to track, but in advanced cases it is more noticeable.
- Sometimes the edges of the cuff may become damaged.Although this does not necessarily indicate that the Hotpoint Ariston bearing needs to be replaced, it can be considered as an additional sign.
- Finally, after finishing the wash cycle, you can simply rotate the drum by hand. If it makes extraneous sounds, for example, clanging or even swaying, an urgent replacement of the bearing in the Hotpoint Ariston washing machine is required.
Step-by-step instruction
Repairing the bearing itself is not practical - it is simply replaced with a new one. This is quite simple to do, but to get to the part, you need to remove all the panels and even remove the tank. This is the main difficulty.
Moreover, this has to be done infrequently, since the elements rarely fail. But if repairs are required, it is necessary to replace both bearings at once, and at the same time the oil seal, even if the spare parts are in relatively good condition.
To figure out how to replace a bearing in an Ariston washing machine, you need to prepare the available tools:
- pliers;
- a set of different screwdrivers, including curly ones;
- hammer;
- a set of wrenches – spanners and open-end wrenches;
- a chisel may also be needed.
Since the analysis is quite complex, and some parts are very heavy, it is better to work together. Replacing the drum bearing of an Ariston washing machine is carried out as follows:
- Turn off the power to the unit, close the tap, remove the hose, and drain the remaining liquid into a previously prepared container. Turn the other way around and unscrew each bolt on the panel at the back.
- Next you need to remove the belt. It is pulled very tightly onto the pulley, so dismantling will require a lot of force. It is recommended to inspect the belt, and if it is very worn, purchase a new one and tighten it on the pulley.
- To ensure that the replacement of an Ariston ARSL 85 or another model bearing is carried out correctly, you need to take several high-quality photographs. This will help when installing the parts in reverse order to reassemble them correctly.
- Then you need to disconnect every element, including the wiring. The sensor that controls the temperature level is removed. They work with it quite carefully, because the part is easy to damage. To properly replace the drum bearing of an Ariston washing machine, remove the heating element and, if necessary, descale it.
- Now remove each pinch bolt that holds the drum rim, as shown in the photo. Remove the gasket and cover.
- Remove the drum and place it on a flat surface.
- Remove the fastening nut, which is located in the center of the shaft.
- Remove the drum cover and carefully place it on the stand. It is better to place a rubber or wooden board, and then start hitting with a hammer to knock the axle out of the bearing.
- Next, the actual replacement of the bearing Ariston AVSL 109 or another model begins. Take a regular straight screwdriver and use it to pry off the oil seal, and then pry off the bearing. Similarly, you need to extract the second of them. Handle them carefully to prevent deformation.
- Finally, the Hotpoint Ariston drum bearing is now being replaced. Place a new part and assemble all the elements, moving in the reverse order.
Do bearings need to be lubricated?
When making repairs, it is worth considering that even if you install new parts, they must be lubricated immediately. Moreover, old bearings need lubrication. Since disassembling the drum is a labor-intensive process, it is better to carry out all the work thoroughly at once and thereby increase the service life of newly supplied spare parts.
For lubrication, heat-resistant and moisture-resistant compounds must be used. At the same time, they should not lead to hardening of the rubber, because otherwise the oil seal will suffer. The system will lose its tightness, causing leaks.
Experienced professionals recommend using the following lubricants:
- AMPLIFON is a high quality Italian product;
- Anderol is a special composition for Indesit washing machines, although it is quite suitable for other brands, including Ariston;
- STABURAGS NBU 12 is a water- and heat-resistant composition that effectively protects bearings from wear;
- LIQUI MOLY is a thick lubricant that can withstand even very high temperatures up to +200 ०C (it is impossible to achieve them at home).
Now it’s clear how to change the bearing on an Ariston washing machine. This is a rather labor-intensive process that requires certain skills. If any difficulties arise, it is better to seek the help of a specialist, since in the absence of experience, self-repair can lead to even greater problems.