How to disassemble a Hansa dishwasher? Do-it-yourself Hans dishwasher repair

It is not difficult to understand how to disassemble a Hansa dishwasher. This requires only available tools and minimal skills. First, the unit itself is prepared, placed on a thick plastic film, then the panels are removed and the parts are removed step by step. Step-by-step instructions with photos can be found in this article.

Preparatory work

Malfunctions of the Hans dishwasher can be associated with various parts that need to be inspected and tested for functionality. To do this, you need to remove each panel and then get to a specific element.

But you must first choose the place where the work will be carried out. It should be spacious enough so that the unit can be approached from any side. If the kitchen does not allow it, it is better to move it into the room and work there.

Also, before repairing the Hans dishwasher with your own hands, you need to complete the preparatory work:

1. Disconnect the unit from power and turn off the tap.
2. Remove all baskets and other containers so that nothing remains in the chamber.
3. If the machine is built-in, unscrew the screws and pull it out.
4. Prepare a basin, unscrew the water supply hose and drain the remaining liquid.
5. Spread thick polyethylene and place the unit on it.

As for tools, it is quite enough to take a set of screwdrivers (regular and curly), an awl and pliers.You may also need a soldering iron and a multimeter. The tool is used to measure resistance, which can be used to judge whether a particular part is working or not.

It is important not only to understand how to disassemble a Hans dishwasher, but also not to forget in what order everything is connected. In order not to get confused, it is better to photograph each step in advance with a mobile phone camera with a high resolution. To get clear pictures, you will also need to use a flashlight.

Step-by-step instruction

Malfunctions of the Hans dishwasher can be associated with a variety of parts. Ideally, you need to check each of them; to do this, the unit is disassembled, proceeding as follows:

1. Using a flat-head screwdriver, hook and remove the bottom panel.
2. Open the door as far as possible and unscrew each screw.
3. Then carefully close it, holding it from the front. Press down and remove the door.
4. We disassemble the Hansa dishwasher correctly. Next, you need to open the door again and remove all the screws from the top end. Dismantle the electronic module and place it in a dry place - it is important to ensure that not even a drop of moisture gets on it.
5. Remove the metal plate that lines the inside of the device door.
6. Remove the soundproofing material (it is also located on the inside of the door). Unscrew each screw that connects the housing to the base.
7. Next, disassembling the Hansa dishwasher consists of disconnecting the spray arm.
8. At the bottom you can see a debris filter. It is twisted counterclockwise and removed. The filter that performs fine cleaning is also dismantled. In appearance it resembles a metal mesh.
9. Unscrew the fasteners that hold the sprinkler from below.It is necessary to prepare a basin to collect the remaining waste liquid.
10. The thermal insulation is removed and the side panels are dismantled.
11. Now the unit needs to be placed upside down and, having disconnected the filler pipe, remove it.
12. Disconnect each wire and remove the pump, which is located in the very center of the pan. The wire is also disconnected from it, and the pump itself in a plastic case is moved in a counterclockwise direction.
13. After removing the pump, the pump is also removed. First loosen the fastenings at the bottom, then remove the drain hose.

Then, if necessary, you can inspect a specific part and “ring” it with a multimeter. If there are signs of a malfunction, it is not advisable to carry out repairs - it is easier to supply a new spare part. Then all the elements are installed in place, moving in the reverse order. Photos taken at each stage will help you understand this.