How to turn on a refrigerator in a cooler

There are coolers in many offices, but not everyone knows how to use the device correctly and turn on the refrigerator mode on it. It is necessary to follow all manufacturer's recommendations to ensure that the device works longer.

Connecting the cooler

Things to consider before installation:

1. Do not place the device near heating radiators or things that heat up.
2. If the device was stored in a cold place, or was transported in winter, before connecting it to the network, it must be unpacked and stored in the room for several hours.
3. If the device was in the wrong position during transportation, it must be put in the correct position for a day before use. Devices containing a compressor should be transported vertically, as there is a risk of loss of the liquid that cools the water (freon).
4. You should not pour bad water into the cooler, such as that drawn from the tap or that contains carbon dioxide.
5. The recommended temperature of the room where the cooler will be located is from 10 to 38 degrees, and the humidity is less than 10 percent.
6. The cooler should be at a distance of 20 cm from the wall or other objects.
7. The cooler must be protected from the sun.
8. Do not store the device at subzero temperatures. If it has been in freezing conditions for some time, it must be turned off for several hours.
9. Do not place foreign objects under the device.
10. It is not recommended to change the position of the device (it should always be vertical).
11. If you are transporting the device or storing it in a room that is not heated, you must first pour out all the liquid that is inside the system. All switches are installed in position O. Unplug it from the outlet. Open the taps and drain the water. If it is very hot, wait until it cools down. Open the valve so that the water begins to drain (it is located on the back wall of the cooler, either in the center of the panel or on the edge).

Note! Before turning on the device, you need to place a container filled with water.

Turning on the refrigerator in the cooler

If a red light is on next to the hot water tap, it means that the water temperature has cooled to 85 degrees, and the cooler is now heating it. You won't be able to make good tea or coffee with this kind of water.

If a green light is on next to the cold water tap, it means that the water temperature is very low, and now it is heating up to 8 degrees. If you try to pour water now, it will be too cold and unsuitable for drinking if the person has a sore throat. To obtain a good temperature, it is better not to use the cooler several times in a row. It is recommended to pour 2 glasses at a time.

Other things to consider before use

1. Remove the sticker from the container. If this is not done, it will fall into the faucet, and you will have to call a technician for repairs. You will also have to get rid of dirt and germs that have gotten into the water.
2. Wipe the water inlet needle with a wet cloth.
3. The container can only be installed vertically. It installs with light pressure. You can't hit it. Then you will need to wait until water is poured into the tank. This will take a few minutes.
4. Do not handle a new bottle with dirty hands.
5. Turn on the hot water and wait until it starts flowing. Draw about a glass of water (this is necessary to remove air from the system).
6. You can connect the cooler to an outlet. If you turn on the device and the system has not yet filled up, the protection will turn on. In this case, you will have to contact the service center.
7. Turn on the toggle switch (it is located on the panel). If 2-3 lights on the front turn on, it means that the cooler turned on successfully and began to warm up the water. The hot one will warm up to 95 degrees, the cold one to 12. But before using the device, you need to wait until all the lights go out.
8. If the refrigerator installed in the cooler has not been used before, you need to let the chamber work for a couple of hours, after which it can be used.
9. To turn off the heating, you must press the switch. Do not unplug it from the socket.

Attention! If the device has been unplugged from the outlet, a few minutes must pass before it can be turned back on.