How to change a light bulb in a refrigerator yourself: even a woman can do it!

Almost every person has a refrigerator in their kitchen. It is indispensable for storing food. The operating principle of refrigerators is quite simple. Even if you purchased “sophisticated” equipment, it is not difficult to operate. you just need to connect it correctly to the power source and set the necessary operating parameters (for the main part and the freezer compartment).

An indicator and indicator of the proper operation of the refrigerator is the light bulb located inside. It also makes the unit convenient to use. But sometimes it turns off temporarily, flickers, or even burns out. So, it's time to replace this light source.

To troubleshoot problems, it is necessary to accurately understand the reason for the lack of lighting. In our article we will share ways to diagnose and identify the causes of damage. In addition, we will tell you how to eliminate the defect and return the lighting to the refrigerator.

Checking the suitability of the lamp

Don't rush to buy a new light bulb and replace it! This may not help if the cause is not electrical and equipment failures. To prevent error Carry out a thorough diagnosis and determine the type of malfunction that has occurred.

• Check wiring in the house. Often problems arise due to chafing or loosening of wires.
• Inspect the outlet and power source. Problems can arise from a poor connection. Plug other equipment into the outlet to check its operation.
• Make sure that electricity is supplied to the apartment as usual. Perhaps there was a power outage throughout the entire house? Try turning on other electrical appliances. If they also do not work, then the reason is the lack of light.
• Observe the operation of a household appliance. Refrigerators usually turn off for a few minutes. This is normal operation. If there is no light for more than 30 minutes, you can assume that the problem is with the light bulb.

If after following all the steps in the instructions the lamp does not light up and the refrigerator is still dark, then the problem lies with the lamp itself. To fix the problem, you need to completely replace it.

IMPORTANT! Some models have features for lighting the device. They appear during work. Check this with sellers or on the website with information about the product.

How to replace a light bulb in domestic refrigerators

There are different types of equipment; we will look at the replacement procedure in each case. First, let's look at Soviet equipment options.

The procedure for replacing the lamp is as follows.

• In advance buy a light bulb of the same brand, which is installed in your refrigerator.
• Unplug the refrigerator from the power supply, remove the cord from the outlet.

ADVICE! If the work takes longer, it is better to remove all products and defrost the system. Remove all water from the chamber.

• Disconnect protective shades, inside of which an incandescent lamp is installed. Disconnect the wiring going to the lamp. If there is tape, remove it as well.

IMPORTANT! In some refrigerators, the slats are held in place by special clamps. It's easy to remove them.Pull the loose ends until they click, then remove the bar.

• After that Unscrew the light bulb from the socket and insert a new one. Then return the lamp and all wires to their original position.
• Plug in the equipment and make sure it is working properly.

ADVICE! Carry out replacement carefully and in compliance with safety regulations. Parts may be very fragile; handle with care.

How to replace a light bulb in imported refrigerators

If you have an imported model at home, the plan of action will be slightly different. These units have interesting lampshades with a complex structure in their design.

To disassemble you will need to perform the following manipulations.

• Turn off the power, defrost the system and remove all food and unnecessary objects that interfere with work.
• Find the lamp mounting location. The transparent lampshade may not be visible from above if there is a large accumulation of ice.
• The cover is secured with three special latches with clamps. Use a minus screwdriver to pry up one of the edges and lift it up. Then carefully remove the remaining holders.
• Unscrew the light bulb from the socket and replace it.
• Now close everything in reverse order and turn on the power.

If replaced correctly, the light should return.

This plan is suitable for most imported products; for a detailed description, read the instructions, check with consultants for details.