What to do if the refrigerator gets very cold?

The key task of a refrigerator is to cool food. Sometimes it starts to get very cold, which is not the norm. Therefore, it is important to detect the malfunction in time and eliminate the cause of excessive frost.

If you find abnormal operation of the refrigerator, you should check its settings. If it is a mechanical model, then the temperature regulator should be between 2 and 3.5. The electronic unit must have a temperature within +4-6 degrees. If the parameters in the settings are normal, but the equipment continues to freeze, you should look for a malfunction.

The main signs that the refrigerator is generating excess cold

To determine that the unit is producing excess cold, you should pay attention to the following signs:

1. The refrigerator is NO FROST, but water is leaking from the freezer. You can see ice inside.
2. Ice has formed in the fruit crates. If you lift the container, water will be revealed.
3. The freezer does not work, but the unit is very cold.

Ice formation is one of the main signs that equipment is freezing excessively.

Elimination of excessive frost in the device depending on the cause of the malfunction

To get rid of such a malfunction, you must first determine the cause that triggered the problem. The breakdown may be trivial, which you can fix yourself. Sometimes the reason is very serious and only a professional can help.

Important! If there is a serious breakdown, you should not try to fix the situation yourself. Otherwise, you can completely break the refrigerator.

Switching the thermostat to the lowest temperature setting

This reason is one of the simplest. It's not common. The thermostat could switch to a low temperature mode on its own. Therefore, it has already been noted that the regulator should be checked. New models are equipped with a button for deep freezing. It is important to make sure that it is not enabled.

Damage to the seal (rubber band) on the refrigerator door

The rubber band could have simply worn out. Warm air will constantly begin to penetrate into the workplace. From here, increased humidity will appear, which will begin to condense and flow into the drainage. Eventually it will begin to accumulate in this area. The problem can be resolved by replacing the seal. This will restore the previous, desired tightness, which will allow the temperature to become optimal.

Drain hole clogged

The hole is located under the vegetable drawers. When it is clogged, the temperature regime is lost. The purpose of drainage is to enable condensate to drain from the refrigeration chamber.When the hole becomes clogged, the liquid remains in the tray and begins to freeze, which negatively affects the products inside the unit. To clean the hole, you need to defrost the equipment and pour warm water into the clogged area.

Freon ran out

The pressure begins to decrease, which leads to non-stop operation of the compressor. This occurs due to the need to compensate for the required temperature regime in the freezer, which negatively affects the temperature in the general compartment of the unit.

Attention! Freon leaks can occur from small cracks, which will greatly complicate the search for the leak location. Therefore, you should refuse to repair yourself.

Clogged or broken valve between different parts of the device

The valve is necessary to switch modes between different compartments. Its malfunction will lead to severe frost in the lower chamber and lack of cold in the lower section. To eliminate the breakdown, you should find the required valve and replace it with a working one.

How to determine the cause of a device malfunction yourself

To determine the cause of the failure yourself, you need to do the following:

1. Checking the settings. It has already been noted that first of all, if there is severe frost in the refrigerator, it is recommended to check the temperature settings. Sometimes this is the problem. If the temperature is ok, you should continue self-diagnosis.
2. Inspection of the seal. The rubber on the door ensures tightness. When it wears out, problems with temperature will begin. Therefore, it is important to check the seal to ensure that it does not fit tightly to the door. If problems are found, you should purchase a new rubber band and replace it.

If the listed parts are normal, then the reason is hidden in other parts.A specialist can make an accurate diagnosis.

In what cases will you need professional help?

Some problems can be fixed on your own. If there is a problem with the controller settings, you need to specify the correct temperature values. When it's a problem with the seal, it needs to be replaced with a new one, but it takes some skill to do the job correctly. In other cases, including a freon leak, clogged drain, or broken valve, you should contact a professional. The work requires certain skills and it will be very difficult to fix the problem yourself.