We repair a Philips blender. How to disassemble a Philips 600 watt blender?

To carry out a quality repair of a Philips blender, you need to disassemble the lid and determine the malfunction by external signs. For example, you can see broken wires, “ring” contacts and clarify the location of the fault. Step-by-step disassembly instructions and repair recommendations can be found in this article.

What you need for work

If you disassemble the Philips nl9206ad 4 blender or other models, you first need to prepare the tools:

• a set of shaped and regular screwdrivers;
• magnet for removing small bolts;
• pliers;
• a knife or metal plate for splitting latches and other parts;
• soldering iron;
• heat gun;
• glue.

You need to disassemble the tool on a flat surface with good lighting in order to notice in time that bolts and other small parts have accidentally fallen off. If in doubt, it is better to photograph the internal structure of the device so that later you can assemble it correctly.

Step-by-step instruction

Disassembly of Philips nl9206ad 4 and other models takes place in several stages. The sequence of actions is as follows:

1. Use a screwdriver or knife to pry off the top cover and remove it.
2. Inside you can see 2 bolts that can be unscrewed with a screwdriver.
3. Next, remove the plastic part.
4. Insert a screwdriver or knife as deeply as possible and pry off the housing.
5. Continue to insert and loosen a little so that the inner part comes out freely from the body.
6. To repair a Philips blender, pry up the plastic attachment and remove it.
7. Unscrew the rotating part, as in the photo. If necessary, it can be removed completely and replaced with a new one.
8. This is what the engine and other parts look like if you remove the entire base from the body.
9. Now you need to carefully inspect the motor and control board - this will help determine the cause of the malfunction and perform the correct repair of the Philips submersible blender.
10. Check the buttons and replace if necessary.
11. The speed controller is also inspected.
12. Next, assemble all the parts of the tool in reverse order and check how it works.

Gearbox repair

Now it’s clear how to disassemble a Philips 600 Watt blender. It remains to consider in more detail the different types of repair work that are carried out in the event of a breakdown of a particular part. To correctly determine the cause, you need to carefully examine the device in assembled and disassembled form, and also listen to how it works.

For example, if after disassembly it is noticeable that the wires have come off the board, you need to prepare a soldering iron and attach them to their original place. It also happens that no breaks are observed, but the brushes supplying the current are worn out. They cannot be repaired - a complete replacement is required. It is not difficult to disassemble the brush, but it should be noted that its petals are quite weak, so it is not advisable to bend them.

If the bearings are worn out, it is necessary to install a new stator winding. As a rule, such types of work are not carried out independently. Therefore, it is better to contact a service center.

Nozzle repair

Another common type of repair work is repairing the Philips blender attachment. Most often, the attachment with knives, which is used for preparing minced meat and puree, breaks.If a knife is worn out, you can sharpen it yourself (if you have the skill) or simply contact a specialist.

But it also happens that the problem is related to the shaft. Then you will need to disassemble the Philips blender - instructions for this process are presented above. It is possible that the shaft is becoming loose due to constant exposure to vibration, causing a gap to form and therefore not rotating properly.

Repair in this case is quite complicated - it is easier to install a new shaft or even purchase another device. But in order to prevent damage and not disassemble the blender too often, it is recommended to periodically tighten the nut that secures the knives.

It is clear how to disassemble a Philips food processor or blender. To do this, you will need ordinary tools - screwdrivers, a knife and others. If you have the skill, you can diagnose the breakdown and fix it yourself. But if you are not sure, you should contact a specialist.