Living and dead water. How to create a device with your own hands?

voda.ua

Do you want to be forever young and beautiful? Like a character from a fairy tale: look just as young and beautiful, live for over 100 years and not complain about anything? Then this article is a must read! In it we will tell you how to make a device for activating water with your own hands from just a couple of items.

Will it be possible to activate water at home and where are the places of “water”?

The healing qualities of these types of water have been known since the times of Kievan Rus. The physical and chemical components of the liquid have not yet been described in detail in any scientific source. Therefore, it is not surprising that it has a limitless impact on the human world and the biosphere: in some situations it gives life, and in others it takes away. And in some situations, water can become a source of healing.

Where is “dead water” located - in swamps, lakes and domestic springs. This is all water from standing springs. According to historians and healers, this category of water is devoid of any beneficial qualities and has no vital energy. It is most suitable for food and household needs. In ancient times, decoctions were made from it.

Sources of living water are stored in mountain streams and waterfalls. This also includes rainwater. All such waters lead to rejuvenation of the body and are beneficial for our general condition.

But these are rather ancient speculations and fairy tales. In modern society, the concept of “alkaline water” is accepted. It is precisely a derivative of living. You can read about its beneficial properties in medical reference books. Let's just say one thing - alkaline water even helps you lose weight!

Scheme for obtaining living and dead water

To make living and dead water with your own hands, you don’t need to go on an expedition to mountain lakes or riverbeds. This type of liquid is quite possible with school knowledge of chemistry and physics. What you need is to create an electrolysis reaction at home. Therefore, water can be called not only “living”, but also “activated”. And the device is an activator.

Research on the structuring of living water was carried out back in the 80s of the last century by leading scientists of the USSR. We don’t know the big results, since all operations were carried out under the heading of secrecy. But if you take the word of traditional healers and healers, some information still leaked out from under the hands of scientists.

Also, when studying the production of living water with their own hands, they used foreign practice. Since it was simply published in magazines and newspapers, it was not something exorbitant and inaccessible.

Modern research has proven that living water receives a negative potential during an electrolytic reaction. It is also called catholyte. From this procedure, the liquid receives regenerating properties. Drinking water helps strengthen the immune system and fight complications after serious illnesses, injuries or operations.

The external and internal use of living and dead water was once approved by Pharm. USSR Committee. He noted its absolute harmlessness and the need to use it for medicinal purposes.

The name of dead water is anolyte. During the electrolysis process, many anodes pass through it - the positive electrode.The properties of dead water come down to the best disinfectant. Just 50 years ago, people used it to disinfect wounds.

Next, we will talk about how to make a device for living and dead water with your own hands.

DIY electromagnetic water converter - detailed instructions

voda.ua

The circuit diagram of the apparatus for living and dead water can be made at home. There is a lot of material on this topic on the Internet, it’s impossible to make a mistake.

To make a device for living water with your own hands, we will need:

• Dielectric plate 150*150 mm.
• High power diodes. We recommend taking models D231 or D232. You can ask stores about foreign analogues.
• Wire with socket. Length is about one and a half meters.
• Glass jar 1 liter – 1 pc.
• A piece of tarpaulin measuring 160*120 mm.
• Food grade stainless steel. Brands are AISI 304 and AISI 316. They must be resistant to acidic environments and active rust. Plate dimensions 180*40 mm.
• Two M6 bolts + nuts.

We drill three holes with a diameter of 6 mm in the dielectric. The distance between the two holes in the middle is 6 cm. The outermost hole is for attaching the power cord. The position doesn't matter. The main thing is to place it near the edge of the future reservoir - a jar.

Take one piece of stainless steel. We mark the future hole with distances: 2 cm in width and 1 cm in length. Drill a 6mm hole. After 20 mm we bend the plate at a right angle. We perform a similar process with the second stainless steel plate.

We screw the stainless steel plates into the middle of the dielectric base. We attach a diode to one. We pass a wire through the outer hole and solder the wires: one to the end of the diode, the second to the base of the plate without a diode.We insulate all exposed parts of the wiring using electrical tape or other material.

We sew a small bag from a piece of tarpaulin so that it is slightly larger in size than a steel plate. Pour water into a glass container and place a canvas bag on the plate with the diode. We lower the device into the jar - it is ready for use.

If the family budget allows you to purchase a ready-made device, then it is better to use this option. It is more reliable than a homemade water vitalizer. You can look on the Internet to see what devices are currently being sold. Or in the comments, if experienced readers in the field write about their purchase and experience.

How to activate water at home

Preparing such water is not difficult and does not require special knowledge. Pour water into a pre-prepared device (purchased or manufactured) onto the bag. We attach the cover to the positive electrode (diode). The water should not reach the neck of the jar and barely cover the cloth bag. More accurate indicators are established in practice.

Making living and dead water with your own hands will take about 5-10 minutes. Important: after the end of the procedure, the resulting liquids should not mix. To do this, drain the container with dead water – a cloth bag – and immediately pour it into another place.

Accuracy is an important component of the process. Do not pour water or put your hands into a device that is plugged into an outlet. All manipulations are performed only with the device turned off!

There is also an alternative to equipment - a bagless electrolyzer. To make it, two jars without a neck are used. It is important that they have straight, plumb edges.The design of the circuit remains unchanged, only the installation must be separate: the anode from the cathode.

What is your experience of drinking living water? How much does digestion and immunity improve? What did you do: a DIY water electrolyzer or a ready-made device? We will be grateful if you share in the comments your ready-made devices for water vitalization at home. Have a nice day!